comoc C130 D 2015, Use And Maintenance Manual, Page: 26 / 48

CHANGING WORKING PROGRAM PARAMETERS
If you need to change the parameters of one of the default programs, do as follows:
1. Press the “SETTING” button on the work screen.
2. As soon as the “SETTING” button is pressed the “MENU” screen is displayed ( Fig.1 ).
3. Press the “PROGRAM SET” button (1) ( Fig.1 ).
4. As soon as the “PROGRAM SET” button is pressed the “SETTING” screen appears (
Fig.2
).
5. Select the program to be modified:
PLUS= “PLUS” working program button.
STD= “STANDARD” working program button.
ECO= “ECONOMIC” working program button.
N.B. : the grey symbols identify the components that are not active. the green symbols identify the
components that are active.
6. Pressing the symbols “+” and “-” regarding the parameter you want to change, the value displayed
is changed.
7. Pressing the “EXIT” button (7) returns you to the “MENU” screen.
N.B.
: exiting the “SETTING” screen the changes made are automatically saved.
N.B. : pressing the “FACTORY” button (6) restores factory settings.
N.B. : in this screen it is possible to change the value of the flow of the detergent (2) in the
machine's water circuit; the value of the flow of water (3) in the machine's water system;
the pressure exercised on the brushes (4); the time for actuating the temporary modifications (5)
of the values of the water in the water circuit and the pressure on the brushes.
N.B. : the amount of detergent varies from a minimum of 0.5% to a maximum of 3% with five
established dosage levels. The correct flow of detergent should depend on the nature
of the floor. It should be proportional to the amount of dirt on the floor and the speed of moving
forward, also remember that the time available for working depends on the amount of water in
the tank.
N.B. : the amount of water varies from a minimum of 2l/h to a maximum of 10l/h with five
established dosage levels. The correct flow of water should depend on the nature of
the floor; It should be proportional to the amount of dirt on the floor and the speed of moving
forward, also remember that the time available for working depends on the amount of water in
the tank.
N.B. : This machine allows you to choose from three different brush pressures by pressing the
button (4) on the command display. the amount of pressure should be selected on the
basis of the type of floor and the amount of dirt. An increase in pressure could cause greater
wear and tear of the brushes and greater energy consumption.
N.B.
: the time for actuating the temporary values is expressed in minutes.
N.B. : the “SETTING” screen can be password protected, see the section “ CONTROLLER
SET ”.
DIPPED HEADLIGHTS
The machine is equipped with front and rear headlights. By turning the main switch (1) to position "I" in
the control panel ( Fig.1 ), the above-mentioned headlights turn on in sidelights mode.
If you need more light in the front of the machine, just press the button (2) on the command display
( Fig.2 ) and the front headlights pass to low beam headlights mode.
N.B. : setting the main switch to “I” the sidelights will come on, and on the instrument panel the
relative symbol will come on (3) ( Fig.2 ).
N.B.
: To switch on the low beam headlights press the button (2) on the instrument panel, the
relative symbol (4) is displayed on the command display
Fig.2
).
N.B. : The low beam headlights are active when the symbol (2) on the instrument panel is green.
EMERGENCY BUTTON
If, during working, there are any problems press the emergency button (1) on the control panel ( Fig.1 ).
N.B.
: As soon as the emergency button (1) is pressed (
Fig.1
) the machine immediately switches
off.
Once you have stopped the machine and solved the problem, to resume work proceed as follows:
1. Turn the main machine switch to "0", turning the key (2) a quarter turn to the left ( Fig.2 ).
2. Set the emergency button (1) to the rest position, turning the key a quarter turn to the right (as
indicated by the arrows marked on it) (
Fig.3
).
3. Turn the main machine switch to "I", making a quarter turn to the right with the key (2) ( Fig.4 ).
N.B.
: Use this button only in case of an emergency. The emergency button is not to be used for
routinely switching off the machine.
BUZZER
The machine is equipped with a buzzer. if you need to sound a warning, just press the button (1) on the
control panel ( Fig.1 ).
RECOVERY TANK FLOAT
The machine is fitted with an electronic device (float) located inside the recovery tank. When the tank is
full, it activates the recovery tank float indicator light (1) on the command display ( Fig.1 ).
If this is the case, proceed as follows:
1. Using the switch on the control panel, select the “TRANSPORT” program (A). The brush motors
and solenoid valve will stop working, and after a few seconds the brush head bodies will lift up from
the floor. The squeegee will remain in contact with the floor for a few seconds, to allow the drying
to finish, after which it will lift up off the floor. A few seconds after the squeegee has reached its idle
position, the vacuum motors will stop working; this is to allow all the liquid in the vacuum tube to be
vacuumed off.
2. Bring the machine to the designated place for draining
off the dirty water, and empty the recovery tank (refer
to “ DRAINING THE RECOVERY TANK ”).
SOLUTION TANK FLOAT
The machine is fitted with an electronic device (float) located inside the solution tank. When the tank is
empty, it activates the solution tank float indicator light (2) on the command display ( Fig.1 ).
If this is the case, proceed as follows:
1. Using the switch on the control panel, select the “TRANSPORT” program (A). The brush motors and
solenoid valve will stop working, and after a few seconds the brush head bodies will lift up from the
floor. The squeegee will remain in contact with the floor for a few seconds, to allow the drying to finish,
after which it will lift up off the floor. A few seconds after the squeegee has reached its idle position, the
vacuum motors will stop working; this is to allow all the liquid in the vacuum tube to be vacuumed off.
2. Bring the machine to the maintenance area and fill the solution tank with detergent solution (refer to
the section titled “ FILLING THE SOLUTION TANK ”).
ATTENTION : when filling the solution tank, it is good practice to drain the recovery tank using the
special drainage tube.
26
Exit Controller info Program set
Hourmeters Alarm Controller set
1
1
2
2
3
4
6 5 7
1
1
2
2
4
1
3
2
2
1 2 1
1
1
1
1 2