manualshive.com logo in svg

Comnet CNGE3FE7MS4, Installation And Operation Manual, Page: 49 / 104

Share
Download
Comnet CNGE3FE7MS4 Installation And Operation Manual Download Page 49

INS_CNGE3FE7MS4_REV–   Rev. 4.30.14   PAGE 49

INSTALLATION AND OPERATION MANUAL 

CNGE3FE7MS4

TECH SUPPORT: 1.888.678.9427

MSTP Instance interface

Label

Description

Instance

Set the instance from 1 to 15

State

Enable or disable the instance

VLANs

Set that VLAN will belong that instance

Proprietary (0-61440) A value used to identify the root bridge. The bridge with the 

lowest value has the highest priority and is selected as the root. If 
the value changes, You must reboot the switch. The value must be 
a multiple of 4096 according to the protocol standard rule.

Apply

Select 

Apply

 to activate the configurations.

MSTP Instance Port interface

Label

Description

Instance

Set the instance’s information except CIST

Port

Select the port that you want to configure.

Priority (0-240)

Decide that port should be blocked by priority in LAN. Enter a 
multiple of 16, 0 through 240. 

Path Cost 
(1-200000000)

The cost of the path to the other bridge from this transmitting 
bridge at the specified port. Enter a number 1 through 
200000000.

Apply

Select 

Apply

 to activate the configurations.

Summary of Contents for CNGE3FE7MS4









































































































Reviews:

No comments