Communications Specialties 3620A Series User Manual Download Page 14

Page 14

Fiberlink® 3620A Series User’s Manual

Fiberlink® 3620A Series

Communications Specialties, Inc. (CSI) warrants that, for a period of three years after 

purchase by the Buyer, this product will be free from defects in material and workmanship 

under normal use and service.  A Return Material Authorization (RMA) number must be 

obtained from CSI before any equipment is returned by the Buyer. All materials must be 

shipped to CSI at the expense and risk of the Buyer.

CSI’s obligation under this warranty will be limited, at its option, to either the repair or 

replacement of defective units, including free materials and labor.  In no event shall CSI be 

responsible for any incidental or consequential damages or loss of profits or goodwill.

CSI shall not be obligated to replace or repair equipment that has been damaged by fire, 

war, acts of God, or similar causes, or equipment that has been serviced by unauthorized 

personnel, altered, improperly installed, or abused.

RMA numbers and repairs can be obtained from:

 

 

Communications Specialties, Inc.

 

55 Cabot Court

 

Hauppauge, NY 11788  USA

 

Tel:   (631) 273-0404

 

Fax:   (631) 273-1638

RMA numbers can also be obtained from our web site: commspecial.com

Please have your serial number available.

Warranty

Summary of Contents for 3620A Series

















Reviews: