manualshive.com logo in svg

CommScope SYSTIMAX iPatch Panel, Manager'S Manual

Share
Download
CommScope SYSTIMAX iPatch Panel Manager'S Manual Download Page 31

Chapter:

 Installing the iPatch Equipment

2–15

Setting Up the Network Connections for the 

Equipment Room

If the iPatch System is to be administered from a PC running the System Manager 
Software, you must configure one iPatch Manager (Rack Manager Plus or Panel 
Manager with Network Manager module installed) in each equipment room to 
communicate with System Manager. The selected iPatch Manager can 
communicate with System Manager either:

ƒ

directly using a 100 Base T Ethernet network, which is a TCP/IP-based data 
network

ƒ

indirectly using a Network Manager LAN (Rack Manager Plus only). The selected 
Rack Manager Plus units in each equipment room are connected to each other 
in series using the NETWORK MANAGER IN and OUT jacks on the back of the 
Rack Manager Plus units. One of the Rack Manager Plus units also is connected 
to an Ethernet network (to which the PC running System Manager is connected).

The following sections describe how to configure a Panel Manager with Network 
Manager module installed for communication with System Manager. For 
instructions on how to configure a Rack Manager Plus unit, see the 

SYSTIMAX

®

iPatch

®

 System Rack Manager Plus Guide

.

Note: 

If you are installing a stand-alone system configuration, skip Task H and 

Task I. Go to “Adding Patch Connections” on page 2–21.

Task H. Finish Connecting the Selected Panel Manager

Perform the steps below to connect the Panel Manager with Network Manager 
module installed to the data network to be used for communication with System 
Manager.

1

Connect a modular patch cord to the 10/100 BaseT jack, on the back of the 
Network Manager module.

2

Connect the other end of the patch cord to the port providing the data network 
service.

3

Use the strain relief strap from the Panel Manager display patch cord to secure 
the power adapter cord to the patch cord inserted in the 10/100 BaseT jack.

Figure 2–12 Connecting the Panel Manager to an Ethernet Network

Patch cord inserted in 

10/100 BaseT jack

Strain relief strap

Network Manager module

Panel Manager

Summary of Contents for SYSTIMAX iPatch Panel
























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands