CommScope RUCKUS E510, Quick Setup Manual

Page: 1 / 4

E510 Access Point
AP Module
Quick Setup Guide
The E510 is a modular outdoor Access Point designed for
deployment scenarios where the antenna structure and onboard
AP intelligence must be physically separated.
In addition to this E510 AP Module Quick Setup Guide, the E510
AP also includes the following documents (please refer to the
relevant documents for detailed information on other E510
modules):
E510 Component Document
E510 Antenna Module (PN#:
902-2101-0000) E510 Access Point Antenna
Module Quick Setup Guide
E510 USB Cable (PN#:
902-2003-0000) E510 Access Point USB Cable
Quick Setup Guide
NOTE: The minimum software revision for the E510 is
ZoneDirector (ZD) 10.1 or later, or SmartZone (SZ) 3.6 or later,
or standalone AP firmware 108.0 or later.
This Quick Setup Guide provides step-by-step instructions on how
to field-install the RUCKUS E510 access point (AP). For detailed
information on planning the installation, performing a site survey
and operating the E510, refer to the RUCKUS Outdoor Access
Point User Guide, available at https://support.ruckuswireless.com.
WARNING! Only trained and qualified personnel should be
allowed to install, replace, or service this equipment.
WARNING! Installation of this equipment must comply with
local and national electrical codes.
CAUTION! Make sure that you form a 80mm - 130mm (3”-5”)
drip loop in any cable that is attached to the AP or the building.
This will prevent water from running along the cable and
entering the AP or the building where the cable terminates.
CAUTION! Be sure that grounding is available and that it meets
local and national electrical codes. For additional lightning
protection, use lightning rods and lightning arrestors.
CAUTION! Make sure that proper lightning surge protection
precautions are taken according to local electrical code.
WARNING! RUCKUS strongly recommends that you wear eye
protection before mounting the AP.
This Guide in Other Languages
• 请
从以下网站
请
得
请
指南的
请
体中文版
https://
support.ruckuswireless.com .
• Vous trouverez la version française de ce guide à l'adresse
suivante https://support.ruckuswireless.com .
•
このガイドの日本語版は
https://support.ruckuswireless.com
でご覧ください。
• 请 请请请请 请请请 请请请 请 请请请 ( https://support.ruckuswireless.com ) 请请
请请请请请 请请请请.
• Veja a versão em português (Brasil) deste guia em https://
support.ruckuswireless.com.
• Puede ver la versión en español (América Latina) de esta guía
en https://support.ruckuswireless.com.
Before You Begin
Before deploying RUCKUS products, please check for the latest
software and the release documentation.
• Release Notes and other user documentation are available at
http://support.ruckuswireless.com/documents .
• Software upgrades are available at http://
support.ruckuswireless.com/software .
• Software license and limited warranty information are available
at http://support.ruckuswireless.com/warranty .
Before deploying your RUCKUS Access Point, verify that all
items listed in Package Contents are included in the package. If
any item is damaged or missing, notify your authorized RUCKUS
sales representative. Also, make sure that you have the
required hardware and tools.
Required Hardware and Tools
• Torque wrench or torque screwdriver with sockets, or SMA
torque wrench, for cable connections
• T10 Security Torx screwdriver/bit for reset button access
• Mounting bracket (purchased separately) for pole mounting
• Customer-supplied mounting bracket for DIN rail mounting
• Electric drill with drill bits and customer-supplied wall anchors,
flat washers, and hex nuts for flat-surface mounting
AP Module Package Contents
The E510 AP Module installation package includes all of the
following:
• E510 Embedded Access Point Module
• Service Level Agreement/Limited Warranty Statement
• Declaration of Conformity
• Regulatory Statement
• RUCKUS AP Getting Started Guide
• This Quick Setup Guide
FIGURE 1 E510 AP Module
Purchased Separately
The E510 requires an Antenna Cable Kit and Antenna Module
(RUCKUS or third-party RF cables) to be purchased separately.
NOTE: BeamFlex is not supported when using third-party RF
cables.
Antenna Module
The E510 Antenna Module (RUCKUS PN# 902-2101-0000) consists
of one vertically-polarized and one horizontally-polarized antenna
per band. Refer to the E510 Antenna Module Quick Setup Guide
for more information.
Antenna Cable Kit
Ruckus provides three different cable kits with different length
cables. Each kit contains two RF coaxial cables and one Control
cable. The RF cables are used to connect the AP Module to the
Antenna Module using two RP-SMA connectors (each dual-band/
single chain).
• 902-2000-0000 E510 Antenna Cable (60 cm length)
Copyright
©
2020 CommScope, Inc. All rights reserved. Page 1 of 4
Published June 2020, Part Number 800-71577-001 Rev D