manualshive.com logo in svg

CommScope iP-600B-12-CSC-SMF, Instruction Sheet

Share
Download
CommScope iP-600B-12-CSC-SMF Instruction Sheet Download Page 13

www.commscope.com 

 

860106376 

Issue 6, December 2012 

 

Page 13 of 13 

Step 6 – Checking the Panel Bus Jumper 

Make sure that the panel bus jumper is still firmly connected to the faceplate (Figure 13). 

Important:

  The connector is keyed. The polarized tab on the panel connector fits into the opening in the header 

connector on the back of the faceplate. 

Step 7 – Installing the Cover 

Install the 184U1 Cover (provided) to shield the shelf from foreign particles. The cover, which is made of clear, 
flame-retardant plastic, slides on and off the shelf. 

To install the cover: 

Slide the cover through the flanges on the shelf until the cover reaches the back wall of the shelf (Figure 13). 

Important:

  Dust covers are installed in the ports to protect the fibers connected to the back of the faceplate. Do 

not remove the dust cover from a port until you connect a patch cord to that port. If you remove a  patch cord 
later, replace the dust cover in the port. 

 

Figure 13  Checking the Panel Bus Jumper and Installing the Cover on the Shelf 

Flange

Dust cover

Panel bus jumper

Back of faceplate

Polarized tab on panel connector

Inside of shelf

Cover

 

Summary of Contents for iP-600B-12-CSC-SMF














Reviews:

No comments

Brands by name

Popular brands

Load more brands