manualshive.com logo in svg

CommScope FlexWave, Installation Manual

Share
Download
CommScope FlexWave Installation Manual Download Page 14

FlexWave

®

 Prism Remote Unit and RF Module Installation Guide

FWPP-504-02

Page 10

© May 2017 CommScope, Inc.

 Overview of Prism Remote Units

 

Remote Unit Status LED 

This section illustrates the Status LED on a Quad-Bay PRU. The Status LED for the Single-Bay, Dual-Bay, and 
Tri-Bay PRUs is in the same location and functions the same as the Status LED for the Quad-Bay PRU.

The Remote Unit has a single red Status LED that is located on the bottom of the chassis. At system startup, the 
Status LED is red to indicate that the Remote Unit is powering up and that the SeRF processor does not yet control 
the Remote Unit; the Status LED will remain red for approximately one minute. If after three minutes the Status 
LED is still red, it indicates the Remote Unit is unable to boot up. (Some common failures that can prevent the PRU 
from booting up include a faulty Power Supply, SeRF, or Compact Flash Card.)

Boom of an AC-Powered PRU

Boom of a DC-Powered PRU

Status  LED

NETWORK

POWER

48VDC/XXA

MOD D

TX1/RX1

NETWORK

MOD D

TX1/RX1

POWER

100-240 VAC

50-60 Hz
XX AMPS

WARNING:
HIGH LEAKAGE CURRENT. EARTH
CONNECTION ESSENTIAL BEFORE
CONNECTING SUPPLY

MOD D

TX0/RX0

MOD D

TX0/RX0

Summary of Contents for FlexWave

































Reviews:

No comments

Brands by name

Popular brands

Load more brands