CommScope FDH 3000 User Manual Download | Manualshive

Page: 29 / 82

background image

ADCP-96-167 • Issue 5 • July 2016

Page 23

© 2016, CommScope, Inc.

5

INSTALLING FEEDER CABLES THAT REQUIRE SPLICING

This section provides instructions for installing feeder cables that will be spliced to the
splitter input fibers. Use the 216B key tool to release and secure the cabinet door as
needed during the feeder cable installation process. This procedure applies to the all-
splice and the combination splice/MPO connector versions of the cabinet.

5.1

Feeder Cable Installation

A compression fitting is provided for securing the feeder cable at the entry/exit point to
the cabinet. Within the cabinet, a cable clamp is used to secure the cable to a bracket.
Beyond the clamp, the outer sheath of the cable is removed to expose the optical
fibers. The feeder cable is typically a 12-fiber cable with stranded or ribbon fiber
construction. Breakout kits should be installed (subject to local practice) to protect the
exposed optical fibers. Grounding kits should be installed on cables with metallic
elements. From the clamping point, the optical fibers are routed to a splice tray for
splicing to the splitter input fibers.

Use the following procedure to install the feeder cable:

1. Locate the compression fitting (on the bottom of the cabinet) that is specified for

feeder cable installation as shown in

Figure 14. Feeder Cable Compression Fitting

2. Open the cabinet door and swing frame to provide access to the interior of the

cabinet.

3. Loosen the compression nut so the feeder cable will slide easily into the cabinet.

Note:

The compression fitting provided with the cabinet can be used with feeder

cables that are 0.35 to 0.63 inches in diameter. Compression fitting kits are
available separately for cables with the following outside diameters: 0.27 – 0.47,
0.51 – 0.71, and 0.71 – 0.98 inches.

COMPRESSION

NUT

COMPRESSION

FITTING

BASE

FEEDER

CABLE

DETAIL OF FEEDER CABLE

ENTRY/EXIT POINT

24302-A

«
...
27
28
29
30
31
...
»

Summary of Contents for FDH 3000



















































































Reviews:

No comments

Related manuals for FDH 3000

Brand: ZALMAN Pages: 6

MySafe C31MYSAFENVME

Brand: i-tec Pages: 40

Brand: Akitio Pages: 9

Elastic Storage System 5147-102

Brand: IBM Pages: 72

ProLiant BL490c - G6 Server

Brand: HP Pages: 101

Brand: HP Pages: 51

ProLiant BL280c G6

Brand: HP Pages: 112

Brand: HP Pages: 25

Brand: HP Pages: 4

DL320s - ProLiant 9TB SATA Storage Server NAS

Brand: HP Pages: 150

D6000 Disk Enclosure

Brand: HP Pages: 54

ProLiant BL495c - G5 Server

Brand: HP Pages: 3

Brand: MikroTik Pages: 2

Brand: Wharfedale Pro Pages: 8

Brand: Datoptic Pages: 2

Stopper STI-1229HTR240

Brand: STI Pages: 2

Opticube VSOF-BS606G

Brand: VISSEM Electronics Pages: 2

Brand: Peavey Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands