background image

 

860576982 
Issue 5, September 2015 
www.commscope.com

 

 

 

Engine 3 Model 4834 Installation 

 

 

 

 

 

© 2015 CommScope, Inc.   

All rights reserved 

 

Page 1 of 7 

 

For RoHS Inquiries:
CommScope Inc.
Corke Abbey, Bray
Co. Dublin, Ireland
Attn: Legal Department

General 

The 

Redwood

®

 Engine 3 Model 4834 powers and communicates with 

Redwood

 gateways, sensors,  and  wall 

switches

 to  provide intelligent lighting control and building intelligence. The engine provides a sophisticated level of 

control  w h i c h   s

ignificantly reduces energy consumption. Multiple engines can be linked together to  power and 

control hundreds or thousands of 

fixtures. 

The engine provides communications and control for all types of lighting including LED, 

fluorescent, CFL  and HID. 

In the case of LED lighting, the engine also provides centralized AC to DC power conversion. It  takes high voltage 
200

–250 VAC or 277 VAC input power, converts it to low-voltage DC, and distributes  the power to all fixtures via 

Redwood

 LED sensors and gateways using Class 2, low-voltage cabling. The engine can be located on a rack or 

wall mounted in an electrical or telecom closet.

 

Ordering information is listed below:  

Part No. 

Description 

ENG-3-4834-250

 

Engine, generation 3, 200

–250 VAC

 

ENG-3-4834-277

 

Engine, generation 3, 277 VAC

 

 WallMount-Tray-1G 

Engine wall mount kit 

 

Redwood

®

 Engine 3 Model 4834 

How to Contact Us 

 

To find out more about 

CommScope

® 

 products, visit us on the web at 

www.commscope.com/

 

 

For technical assistance: 

-

 

Live technical support for 

Redwood

®

 products is available Monday through Friday from 

8 AM to 5 PM (PST), excluding holidays. 

-

 

Within North and South America, contact your local account representative or technical 
support at 1-800-840-0709 (Option 2).  Outside North and South America, contact your 
local account representative or technical support at +1 510-270-5360 (Option 2). 

-

 

An email can also be sent to [email protected] for technical support. 

 

Summary of Contents for Engine 3 Model 4834








Reviews: