background image

ADCP-90-326 • Rev B • November 2020

Page 7

© 2020, CommScope Inc.

3. If damage is detected or if parts are missing, file a claim with the commercial carrier and

then notify CommScope Customer Service. Save damaged carton for inspection by the
carrier.

4. Refer to 

Section 8 Customer Information and Assistance

 for repair, replacement, and

warranty information.

5. Save the shipping container for use if equipment requires shipment at a future date.

4 MOUNTING THE FMT ON THE RACK

For all mounting options, the FMT uses two mounting brackets, one on either side, with two
mounting holes in each bracket (see 

Figure 4

). Determine what recess is required and adjust

mounting brackets for the required recess. Secure tray to rack using the screws (provided).

Figure 4. FMT Mounting Holes

5 INSTALLING VERTICAL CABLE GUIDES

Optional vertical cable guides (VCGs) may be installed with FMTs when space permits. 

Table 2

summarizes possible uses of VCGs for various combinations of rack width and recess.

1. If the rack width is 19 inches (48.26 cm) or ETSI (20.28 inches, 51.5 cm) and:

Note: 

In some configurations, the same screw is used for both the mounting bracket (top

hole) and the vertical cable guide (see 

Section 5 Installing Vertical Cable Guides

).

Table 2. Possible Uses of VGCs

RACK WIDTH

RECESS

VERTICAL CABLE 

GUIDE

19 inches 

(48.26 cm)

40 mm (1.54 inch)
2.2-inch (5.59 cm)

VCGs not advised

3.1-inch (7.9 cm)
5-inch (12.7 cm)

6.5-inch (16.5 cm)

Figure 5

23 inches 

(58.42 cm)

40 mm (1.54 inch)
2.2-inch (5.59 cm)
3.1-inch (7.9 cm)
5-inch (12.7 cm)

6.5-inch (16.5 cm)

Figure 6

20200-A

MOUNTING

HOLES

Summary of Contents for ADCP-90-326



























Reviews: