manualshive.com logo in svg

CommScope 760242401, User Manual

Share
Download
CommScope 760242401 User Manual Download Page 2

Page 2 of 22. 

© 2020 CommScope, Inc. 

TC-96292-IP

1

Product Description

1.1 General Description

The Flex Frame (ODF-FF19CM) shown in 

Figure 1

, is an optical distribution frame providing a

connection point between facility cables in a data center. Facility cables are high-fiber-count
cables containing rollable ribbons, and of a type suitable for being routed indoors or outdoors.
The basic product consists of a 19-inch seismic rack with two cable managers, one on each side.
Two sizes are offered: ODF-FF19CM-40RU, which has 40 rack units of connector panel spacing,
and ODF-FF19CM-36RU, which has 36 rack units. 

The ODF-FF19CM is also offered with an integral Splice Cabinet (ODF-FF19CM-36RU-SP). The
Splice Cabinet is installed on the back of the left cable manager (when viewed from the front).

Figure 1.  Flex Frame (Front Isometric View), ODF-FF19CM Shown

FRONT

TROUGH

27250-A

HANGING

HOLE FOR

PATCH

CORD

ROUTING

GUIDE

19-INCH

SEISMIC

RACK

Summary of Contents for 760242401























Reviews:

No comments

Brands by name

Popular brands

Load more brands