8
3
ALARM SPECIAL FEATURES
WARN-AWAY
Dual zone shock sensor, zone one when triggered activates causes the alarm to chirp five times
indicating a Warn-away condition, second zone when active, triggers the Alarm.
VALET MODE
Valet mode entry
.
Disarm the alarm, turn the Ignition ON, and hold the push button valet switch
for 5 seconds until LED turns ON and parking light flash once. Door lock/ unlock, and all aux
outputs respond to transmitter activation (Keyless Entry).
Valet mode ext.
Turn the Ignition ON; hold the push button valet switch for 5 seconds until
LED turns OFF and parking light flash twice.
EMERGENCY OVERRIDE
Disarm the alarm without transmitters. Turn Ignition ON, hold the push button switch down for
5 seconds, the siren will turn off and alarm will disarm.
If emergency coded override is programmed then turn ignition on, press the push button switch
the number of times that correspond to the pre programmed code, hold the push button switch
down for 5 seconds, the siren will turn off and alarm will disarm.
SENSOR DISABLE FEATURE
Disable the sensors for a single arm cycle, by pressing the 1st button to Arm and within 10
seconds pressing the 1st button again. The siren and parking light will flash five times,
that will eliminate sensor for that arm cycle. Rearming the alarm will re-enable the sensor.
ACCIDENTAL DISARM (AUTO REARMING)
If the alarm has been armed for at least 10 seconds and has been disarmed with the transmitter
by mistake. It will automatically rearm itself within 30 seconds. Opening the door or turning on
the ignition key will cancel rearming. This feature will be always active no matter if the alarm
is in active or passive mode.
To disable this feature, go to programming mode and turn this feature to OFF.
DOOR TRIGGER DELAY IN PASSIVE MODE
If enabled, when the alarm arm’s passively, upon opening the door siren will chirp for 10 seconds
then will trigger the alarm, unless you turn the ignition on within that 10 seconds. This will disarm
the system. This enables you to use the alarm without remote
SECURE AUXILIARY OUTPUTS
Each auxiliary output can be programmed so that it can be activated only when the system is
disarmed and the ignition switch is off.
This feature is particularly useful when the output is used for trunk release purpose. This prevents
the trunk to be released accidentally by pressing the trunk release button.
PERRSONALIZED OVERRIDE CODE
To select you personal security code to override the alarm. Go to access feature programming
mode location # 4, press button # 3 on the transmitter, select your personal security code by
pressing the valet switch to a desired number (1 to 15), then turn the ignition off.To disarm the
alarm when triggered, turn ignition on press the valet switch to the selected number times and
hold for 10 seconds on the last press until the alarm turns off.
PROGRAMING TRANSMITTERS
Turn the ignition key 3 times on/off; leave the ignition key in ON position, within 3 seconds
siren will chirp 3 times.
Press valet switch for 5 seconds the siren will chirp 5 times and LED comes on solid, then press
button # 1 on the remote transmitter one time. The siren will chirp once, press button #1 one
more time the siren will chirp twice this will confirm that the alarm has learned that
transmitter. If you want to teach another transmitter with a different code press button # 1 one
time on the second transmitter the siren will chirp once. Then press button #1 one more time
on the transmitter siren will chirp twice you can teach 4 different codes.
TRANSMITTER TEACHING FOR SECOND CAR OPERATION
Same as programming transmitter, but press the 5 the or function button 2 times then press button
# 1, siren will chirp once then repeat procedure one more time, siren will chirp twice indicating it
learned the transmitter
TWO WAY FM REMOTE OPERATION
Button #1
Door Lock / Unlock
Arm & Disarm
Press AND Hold for PANIC
Button #3
TRUNK OPEN
Button #2
REMOTE ENGINE
START
Antenna
LCD Display
Press Button 2 & 3 And Hold for
program
CLOCK
Then Button #
2 hour,
Button #
3
mints.
When set time press Button #1 to
EXIT.
Repeat same Programming for
Alarm Clock and Start Clock
Button #1 =
Arm & Disarm
Button #2 =
Remote Engine Start
Button #3 =
Trunk Open
Button #4 =
3rd Channel ( programmable)
Button #5 = Backlight & (Programming)
Button #2&3 = (PROGRAM)
CLOCK/ALARM CLOCK/START CLOCK
Button #4
--
3rd
CHANNEL
*
Button #5
Backlight &
Programming
STATUS,CHIRP ENABLE &
DISABLE
REMOTE SOUND ENABLE
& DISABLE
LOCATION
1 - CLOCK
2 - ALARM CLOCK
3 - AUTO START CLOCK
TWO WAY FM PAGER PROGRAMMING
Installing the Two Way FM Pager requires teaching the Alarm system the FM pager interface
module ID code. It is accomplished in step 22 of the programming table.
Connect the interface module to the Alarm system, enter step 22 in the programming table,
press button #1, of the one-way transmitter.
Additional FM transmitter is also programmed in step 22 of the programming table.
The procedure is:
Enter step 22 in the programming table, press button #2, of the two-way transmitter.
DRIVER CALLING:
When alarm is in disarm mode, press
VALET
Push Button switch momentarily will Page the
remote with 4 Beeps to indicate a calling function from the Vehicle.
Lock/Unlock
Trunk release
Engine running
Valet mode
Parking lights
Shock sensor trigger
Driver
calling
Engine starting
Antenna tranmitting
Alarm clock mode
Clock
hour,minute indication
Accessorie Currently Available:
•
•
•
•
•
Channel Expander
•
•
•
•
•
battery status
Siren alert
