background image

P. 8 

User Guide

 

 

2.

 

The parking lights will flash once and the LED will flash slowly to confirm that the doors 

have been locked and that the Starter Kill feature is enabled (if it was installed). 

To  UNLOCK  your doors and  DISARM  the Starter Kill: 

1.

 

Press and hold the 

UNLOCK

 button for approximately 1 sec. 

2.

 

The parking lights will flash twice and the LED will go out to confirm that the doors have 

been unlocked and that the Starter Kill feature is disarmed if it was installed. 

Note: 

If installed and configured in Passive Mode at installation, the Starter Kill feature will 

rearm automatically 60 seconds after the doors are unlocked. For that reason, you may 

have to unlock your doors a second time if some time elapses before you actually start 
the engine. 

Priority Door Access 

If the remote door locks option is installed on your vehicle, this safety feature allows you to 
unlock solely the driver’s door with a single press of the 

UNLOCK

 button on the transmitter; 

upon a second press of the 

UNLOCK

 button, all the other doors will unlock. 

Ignition-controlled Door Locks Option  

This is an added security feature. If your system was installed with the Ignition-controlled 

Door Locks option, the doors will automatically be locked as soon as the user presses the 

brakes while the ignition key is in the 

IGNITION ON (RUN)

 position. 

When the key is turned to the Ignition 

OFF

 position, the doors will automatically be unlocked. 

(Only available if remote Door Lock Option is installed) 

Secure Lock Option 

Before it can remote start your vehicle, the module must first disarm the factory security 

system. 
The Secure Lock feature may be required on certain vehicle models with factory security 

systems that automatically unlock the doors when the security system is disarmed. 

To keep your vehicle protected when the factory security system is disarmed for a remote 

start, Secure Lock will relock your doors as soon as the vehicle has started. 
Once the engine run cycle ends, Secure Lock will rearm your factory security system. 

Remote Trunk Release Option 

If your system was installed with the Remote Trunk Release, you can open your trunk by 

pressing the

 TRUNK 

button on the remote transmitter.  Vehicles must have an electric 

TRUNK 

switch or a remote 

TRUNK

 button on the vehicle’s OEM Transmitter for this option to be 

compatible with the Module. 

Starter Kill / Anti-Grind 

This added security feature will immobilize your vehicle when the system is armed (

LOCKED

). 

If your Module was installed with the Starter Kill option, you will not be able to start your 

vehicle with the key unless the system has been disarmed first (

UNLOCKED

). 

The Starter Kill option can be programmed to be 

ACTIVE

 (will not arm automatically) or 

PASSIVE

 

(will arm automatically). In 

PASSIVE

 Mode, your installer can program it to arm automatically in 

1 or 3 minutes.   

Once the vehicle has been remote started, the Anti-Grind feature prevents the starter motor 

from re-engaging when the ignition key is accidentally turned to the 

CRANK 

position.   

Note:

 Automobile insurance companies sometimes offer a rebate for vehicles with a 

passive starter kill device.  

Summary of Contents for CS-396i












Reviews: