Comm-Tec DAN-B202 User Manual Download Page 14 | Manualshive

Page: 14 / 24

background image

14

Dante interface 2x2

5. Operation of Web-UI

DAN-B202 can be controlled via web-based GUI. It allows users to interact with
DAN- B202 through graphical icons and visual indicators.

1) When Dante device connects with the computer directly and

don’t change the

default IP address, please type

169.254.1.178

in your browser to access Web-UI.

2) If Dante device is assigned IP address by router, please find the device in
Network page of the computer, then click the device to access Web-UI.

It will enter the log-in interface shown as below:

The default user name is

“admin” and password is “admin”.

«
...
12
13
14
15
16
...
»

Summary of Contents for DAN-B202

























Reviews:

No comments

Related manuals for DAN-B202

Brand: Keithley Pages: 32

Brand: jcb Pages: 166

Brand: 3M Pages: 2

Infield Rascal Pro

Brand: ABI Attachments Pages: 8

Brand: Abicor Binzel Pages: 84

Brand: ABI Attachments Pages: 5

Brand: abem Pages: 47

Brand: Abely Pages: 5

Brand: Bard Pages: 144

Brand: GALBIATI Pages: 8

Brand: Vahva Jussi Pages: 9

Crouse-hinds series

Brand: Eaton Pages: 32

Brand: Oakworks Medical Pages: 28

Brand: Naked Pages: 36

Brand: PacBio Pages: 13

Brand: Pablo Pages: 4

Brand: PA Pages: 28

Brand: Yamaha Pages: 39

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands