Comfortflame.US.com
900579-00_NC
11
Ignitor
Control Knob Pilot
FROM "PILOT" POSITION
SLIGHT PUSH TO
TURN OFF
PULL PUSH
TO LIGHT
ON
ON
FROM "PILOT" POSITION
SLIGHT
PUSH T
O
TURN OFF
PULL
PUSH
TO LIGHT
FROM "PILOT" POSITION
SLIGHT
PUSH T
O
TURN OFF PULL
PUSH
TO LIGHT
ON
OFF
On
Off
OFF
OFF
Figure 18 - Ignitor and Control Knob
OPERATION
FOR YOUR SAFETY
READ BEFORE LIGHTING
WARNING: Keep flue open when operating unit.
WARNING: If you do not follow these instructions
exactly, a fire or explosion may result causing property
damage, personal injury or loss of life.
BEFORE LIGHTING smell all around the appliance area for gas. Be
sure to smell next to the floor because some gas is heavier than
air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electric switch; do not use any phone in your
building.
• Immediately call your gas supplier from a neighbor’s phone.
Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire department.
LIGHTING INSTRUCTIONS
1. STOP! Read the safety information, above.
2. Turn the gas shutoff valve to OFF.
3. Wait five (5) minutes to clear out any gas. If you then smell gas
STOP! Follow the safety information above. If you don‘t smell gas,
go on to the next step.
4. Lay a lit match on top of pan material about 2" from end of supply
side of pan.
5. Slowly turn gas shutoff valve ON until burner ignites. If burner
does not ignite within 10 seconds with match burning, turn shutoff
valve OFF and repeat steps 1 through 4 again.
GAS SHUTOFF
VALVE OPERATION
Flame Adjustment
Adjust the flame ON/OFF by turning the gas shutoff valve counter-
clockwise
to open or clockwise
to close, as necessary.
Shutting Off Appliance
Turn gas shutoff valve clockwise
to the OFF position.
CURING
LOGS
During the 2-3 hour appliance break-in period, you may detect an
odor from the appliance as the various paints and compounds used
in the manufacturing of this log set cure. This is a normal and tem-
porary situation that is not cause for alarm. However, you may want
to provide extra ventilation to the room during this time.
To ensure proper curing of the logs:
• Ignite a 2" flame and maintain it for 1 hour.
• Burn the logs in consecutive 1 hour periods raising the flame an
additional 2" to full flame height for a total of three hours.
OPERATING INSTRUCTIONS
FOR GA9050A-1 (F0235)
Note:
Operation instructions for GA9150A (F0237) Remote Ready
ON/OFF Safety Valve/Pilot Kit will be included with the kit.
1. STOP! Read the safety information, column one.
2. Make sure equipment shutoff valve is fully open.
3. Press in and turn control knob clockwise
to the OFF posi-
tion.
4. Wait five (5) minutes to clear out any gas. Then smell for gas
around log set and near floor. If you smell gas, STOP! See safety
information, page 3. If you don’t smell gas, go to the next step.
5. Turn control knob counterclockwise
to the PILOT position
and press in. Keep control knob pressed in for five (5) seconds.
Note:
You may be running this log set for the first time after
hooking up to gas supply. If so, the control knob may need to be
pressed in for 30 seconds. This will allow air to bleed from the
gas system.
• If control knob does not pop up when released, contact a quali-
fied service person or gas supplier for repairs.
6. With control knob pressed in, push down and release ignitor
button. This will light pilot. The pilot is attached to the rear of the
front burner. If needed, keep pressing ignitor button until pilot
lights.
Note:
If pilot does not stay lit, contact a qualified service person
or gas supplier for repairs. Until repairs are made, light pilot with
match.
7. Keep control knob pressed in for 30 seconds after lighting pilot.
After 30 seconds, release control knob.
Note:
If pilot goes out, repeat steps 3 through 7.
8. Turn control knob counterclockwise
to the ON position.
Burner should light. If burner does not light, call a qualified service
person.
9. To shut off burner only leaving pilot lit, turn control knob clockwise
to the PILOT position.
