OWNER’S MANUAL
517.787.2100 • www.marsdelivers.com
READ AND SAVE THESE INSTRUCTIONS
Attention: Pictures in this manual are for reference only.
Model
20” Box Fan
FF-2030Dxx-PBL
FF-2030Dxx-PWH
PART FIGURE
1. Top Cover
2. Switch Knob
3. Front Grill
4. Rear Grill
5. Blade
6. Side panel
7. Base cover
8. Supporting
9. Rubber feet
OWNER’S MANUAL
20" Box Fan
MODEL: FB50-16H
READ AND SAVE THESE INSTRUCTIONS
Version 1.0 2015
Attention: Pictures in the IM are for reference only.
1
2
3
4
5
8
9
7
6
OPERATING INSTRUCTION
Speed control
Speed is controlled by the switch knob:
0--Off 1---Low 2---Medium 3--High
1. Never insert fingers, pencils, or any other object through the grille when fan is
running.
2. Disconnect fan when moving from one location to another.
3. Disconnect fan when removing grilles for cleaning.
4. Be sure fan is on a stable surface when operating to avoid overturning.
5. Do not use fan in window. Rain may create electrical hazard.
6. Ensure that the fan is switched off from the supply mains before removing the grille.
The rules about cord and plug as below:
1. This product employs overload protection (fuse). A blown fuse indicates an
overload or short-circuit situation. If the fuse blows, unplug the product from the
outlet. Replace the fuse as per the user servicing instructions (follow product
marking for proper fuse rating) and check the products. If the replacement fuse
blows, a short-circuit may be present and the product should be discarded or
returned to an authorized service facility for examination and/or repair.
2. Do not operate any fan with a damaged cord or plug. Discard fan or return to an
authorized service facility for examination and/or repair.
3. Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or
similar coverings. Do not route cord under furniture or appliances. Arrange cord
away from traffic area and where it will not be tripped over.
Read Rules for Safe Operation and Instructions Carefully.
1. This appliance has a polarized plug (one blade is wider than the other). To reduce
the risk of electric shock, this plug is intended to fit in a polarized outlet only one
way. If plug does not fit fully in the outlet, reverse the plug. If it still does not fit,
contact a qualified electrician. Do not attempt to defeat this safely feature.
2. To reduce the risk of fire or electric shock, DO NOT use this fan with any solid-
state speed control devices.
CAUTION
WARNING
RULES FOR SAFE OPERATION
a) Grasp plug and remove from the receptacle or
other outlet device. Do not unplug by pulling
on cord.
b) Open fuse cover. Slide open fuse access
cover on top of attachment plug towards blades.
c) Remove fuse carefully. Insert the tip of your tool
into fuse slot (close with the terminal), then prize
the fuse gradually and slowly, but not overexert. If you feel tight, you can try it at
several times and prize the fuse little by little. When one side of the fuse has
been prized, then you can get the fuse out entirely.
d) Risk of fire. Replace fuse only with 2.5 Amp, 125 Volt fuse.
e) Close fuse cover. Slide closed the fuse access cover on top of attachment plug.
f) Risk of fire. Do not replace attachment plug. Contains a safety device (fuse) that
should not be removed. Discard product if the attachment plug is damaged.
Notice:
1. When you replace the fuse, please don’t operate suddenly or overexert, or else
the product will be damage or cause accident.
2. When you feel it hard to be operated, please make sure you have got the right
way.
USER SERVICING INSTRUCTIONS
CLEANING
1. Be sure to unplug from the electrical supply source before cleaning.
2. Plastic parts should be cleaned with mild soap and a damp cloth or sponge.
Thoroughly to remove soap film with clean water.
3. Be sure not to make water or other liquid enter inside of motor.
Take out the fan from the packing carton
,
place the fan upside down
,
rotate the
support 90° counterclockwise to make it on the using position
(
Fig 2
)
then turn
the fan upright.It will be ready to work when you plug.(Fig 3)
ASSEMBLY OF FAN
Fig.1
Fig.2
Fig.3
Rotate the support 90°
Location for the bracket
when using.
1
2
