ComAp InteliNano NT Plus Reference Manual Download

Page: 50 / 90

InteliNano-NT Plus, SW version 2.0.1.x,

©ComAp – July 2015

I20

Low Fuel Level

When this binary input is activated the red LED above

Stop

button will blink, the general warning

symbol will be displayed on LCD’s upper right corner, and

Low Fuel Level

symbol will be displayed

on event log with running hours stamp. This alarm is only warning. For more details see

Warning

procedure in chapter

12 Alarm, Events and History Management.

OTE

Input has 10s delay.

I21

Fuel Level Analog

Analog input for fuel level measurement. When measured value exceeds the preset threshold, the left
red LED above

Stop

button will blink, the general warning symbol will be displayed on LCD’s upper

right corner, and fuel level symbol will be displayed on event log with running hours stamp. This alarm
is only warning. For more details see

Warning

procedure in chapter

12 Alarm, Events and History

Management.

Alarm threshold is 20% of measurement range. You can choose one from two preset resistive
sensors (VDO, Datcon) or you can create your own sensor curve.

OTE

Input has 10s delay.

VDO Level %

Ohm

180

100

Summary of Contents for InteliNano NT Plus



























































































Search results

Summary of Contents for InteliNano NT Plus

Reviews:

Related manuals for InteliNano NT Plus

Brands by name

Popular brands

ComAp InteliNano NT Plus, Reference Manual

Search results

Summary of Contents for InteliNano NT Plus

Reviews:

Related manuals for InteliNano NT Plus

Brands by name

Popular brands