ComAp InteliLite MRS16 Manual Download Page 613

Page: 613 / 632

InteliLite Global Guide

613

The firmware update process may be performed via any kind of connection including connection via the same

module in which the firmware is to be updated. The connection is reestablished again automatically when the

update process is finished.

Extension modules

EM-BIO8-EFCP

613

EM-BIO8-EFCP

EM-BIO8-EFCP is optional plug-in card. Through this card controller can accommodate one AC current (CT)

measuring input (1A or 5A input) and up to 8 binary inputs or outputs. In LiteEdit2015 PC configuration tool it is

possible to easily choose if particular I/O will be binary input or output.

Image 9.25 EM-BIO8-EFCP interface

IMPORTANT: Any manipulation with plug-in module shall be done with disconnected power

supply to controller.

IMPORTANT: Earth fault current measurement is supported by controller only in slot A.

Summary of Contents for InteliLite MRS16

























































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for InteliLite MRS16

Reviews:

Brands by name

Popular brands

ComAp InteliLite MRS16, Manual

Search results

Summary of Contents for InteliLite MRS16

Reviews:

Brands by name

Popular brands