manualshive.com logo in svg

ComAp InteliLite MRS16, Manual

Share
Download
ComAp InteliLite MRS16 Manual Download Page 598

InteliLite Global Guide

598

Alarm Type

BOC

Alarmlist message

BOC Gen Voltage Unbalance ph-n

Alarm evaluated

Generator excited only

Related applications

AMF, MRS

Description

This alarm evaluates the unbalance of the phase voltages, i.e. the difference

between highest and lowest phase voltage at any given time. The following

setpoints are related to it:

Voltage Unbalance BOC (page 200)

adjusts the maximum allowed difference

between the highest and lowest phase voltage at any given time.

Voltage Unbalance BOC Delay (page 200)

adjusts the alarm delay.

BOC Gen Voltage Unbalance ph-n

6

back to List of alarms level 2

Alarm Type

Shutdown

Alarmlist message

Sd + Name of binary input

Alarm evaluated

Generator excited only

Related applications

AMF, MRS

Description

The overcurrent alarm is based on IDMT principle. The reaction time of an IDMT

alarm is not fixed, but depends on how much is the protected value (generator

current in this case) above the limit (

Nominal Current (page 156)

). The higher is the

overcurrent, the shorter the reaction time will be. All generator phases are

evaluated.

The behaviour of the overcurrent alarm is adjusted by the following setpoints:

IDMT Overcurrent Delay (page 196)

defines the reaction time of the

protection when the current is twice the amount of nominal value.

Nominal Current (page 156)

set the nominal current level, where the alarm

starts to be evaluated. The reaction time is infinite at this point.

BOC Overcurrent IDMT

6

back to List of alarms level 2

Alarm Type

BOC

Alarmlist message

BOC Overload

Alarm evaluated

All the time

Related applications

AMF, MRS

Description

The alarm is issued when the gen-set power is over the limit for time period longer

than the delay. The behavior of the overload alarm is adjusted by the following

setpoints:

Overload BOC (page 194)

adjusts the overload limit.

Overload BOC Delay (page 194)

adjusts the delay

BOC Overload

6

back to List of alarms level 2

Summary of Contents for InteliLite MRS16

























































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands