manualshive.com logo in svg

ComAp InteliLite MRS16, Manual

Share
Download
ComAp InteliLite MRS16 Manual Download Page 156

InteliLite Global Guide

156

Setpoint group

Basic settings

Related FW

1.2.1

Range [units]

1 .. 5 000 [kW]

Default value

200 kW

Alternative config

Yes

Step

1 kW

Comm object

8276

Related applications

AMF, MRS

Config level

Standard

Setpoint visibility

Always

Description

Nominal power of the gen-set. Generator

Overload BOC (page 194)

protection is based on this setpoint.

Note:

This setpoint is used when setpoint

Connection type (page 157)

is adjusted to Monophase or

Splitphase or 3Ph3Wire or High Leg D or 3Ph4Wire or when Autodetect detects connection type as

3Ph3Wire or High Leg D or 3Ph4Wire.

Nominal Power

6

back to List of setpoints

Subgroup: Current settings

Setpoint group

Basic settings

Related FW

1.2.1

Range [units]

1 .. 10 000 [A]

Default value

350 A

Alternative config

YES

Step

1 A

Comm object

8275

Related applications

AMF, MRS

Config level

Standard

Setpoint visibility

Conditioned by the setpoint

Connection type (page 157)

.

Description

It is current limit for generator

IDMT Overcurrent Delay (page 196)

and

Short Circuit BOC (page 195)

protections and means maximal continuous generator current. Nominal Current can be different from

generator rated current value.

Note:

To lock this setpoint against editing you also have to lock setpoint

Nominal Current 1 (page 291)

and

Nominal Current 2 (page 293)

.

Nominal Current

6

back to List of setpoints

Summary of Contents for InteliLite MRS16

























































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands