ComAp InteliLite MRS16 Manual Download Page 268

Page: 268 / 632

InteliLite Global Guide

268

Setpoint group

Scheduler

Related FW

1.2.1

Range [units]

[-]

Default value

[-]

Alternative config

Step

[-]

Comm object

Related applications

AMF, MRS

Config level

Standard

Setpoint visibility

Conditioned by the setpoint

Timer 1 Function (page 264)

Description

Refresh period of

Timer 1 Function (page 264)

. Meaning of this setpoint depends on type of repetition

adjusted in

Timer 1 Repeated (page 267)

Daily

Range [units]: 1 .. 1000 [day]. This setpoint adjust that every X day the timer will be

activated.

Example:

If you have daily repetition and you set this setpoint to 2, then every

second day from first occurrence of

Timer 1 Function (page 264)

, the

Timer 1

Function (page 264)

will be activated.

Weekly

Range [units]: 1 .. 60 [week]. This setpoint adjust that every X week the timer will be

activated.

Example:

If you have weekly repetition and you set this setpoint to 2, then every

second week from first occurrence of

Timer 1 Function (page 264)

, the

Timer 1

Function (page 264)

will be activated in selected days adjusted by

Timer 1 Day

(page 269)

Monthly

Range [units]: 1 .. 12 [month]. This setpoint adjust that every X month the timer will be

activated.

Example:

If you have monthly repetition and you set this setpoint to 2, then every

second month from first occurrence of

Timer 1 Function (page 264)

, the

Timer 1

Function (page 264)

will be activated in selected day of month adjusted by

Timer 1

Repeat Day In Month (page 270)

or in selected days of week of month adjusted by

Timer 1 Day (page 269)

and

Timer 1 Repeat Week In Month (page 271)

Short Period

Range [units]: [HH:MM]. This setpoint adjust that every X short period the timer will

be activated.

Example:

If you have short period repetition and you set this setpoint to 2, then

every second minute from first occurrence of

Timer 1 Function (page 264)

, the

Timer 1 Function (page 264)

will be activated.

Timer 1 Refresh Period

back to List of setpoints

Summary of Contents for InteliLite MRS16

























































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for InteliLite MRS16

Reviews:

Related manuals for InteliLite MRS16

Brands by name

Popular brands

ComAp InteliLite MRS16, Manual

Search results

Summary of Contents for InteliLite MRS16

Reviews:

Related manuals for InteliLite MRS16

Brands by name

Popular brands