ComAp InteliLite MRS16 Manual Download Page 188

Page: 188 / 632

InteliLite Global Guide

188

Setpoint group

Engine settings

Related FW

1.2.1

Range [units]

Disabled / 1 .. 60 [s]

Default value

30 s

Alternative config

YES

Step

1 s

Comm object

10685

Related applications

AMF, MRS

Config level

Advanced

Setpoint visibility

Visible only if the logical binary output

is configured

Description

If the controller does not see the fuel increase during fuel transfer within this time alarm

Wrn Fuel Transfer

Failed (page 581)

will be displayed and the

will be turned off. Alarm

Wrn Fuel

Transfer Failed (page 581)

will be displayed but this alarm becomes immediately inactive and it will be

possible to delete this message by the Fault reset button. If the fault is deleted the controller will initiate the

transfer again.

Transfer Wrn Delay

back to List of setpoints

Subgroup: Maintenance

Setpoint group

Engine settings

Related FW

1.2.1

Range [units]

0 ... 9 999 [h] / Disabled

Default value

1 000 h

Alternative config

Step

1 h

Comm object

10528

Related applications

AMF, MRS

Config level

Standard

Setpoint visibility

Always

Description

Maintenance timer 1 counts down when engine is running. If reaches zero, an alarm appears. When the

value 10000 is set, than the Maintenance function is disabled and counter does not count. Counter value

disappear from controllers statistics.

Maintenance Timer 1

back to List of setpoints

Summary of Contents for InteliLite MRS16

























































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for InteliLite MRS16

Reviews:

Related manuals for InteliLite MRS16

Brands by name

Popular brands

ComAp InteliLite MRS16, Manual

Search results

Summary of Contents for InteliLite MRS16

Reviews:

Related manuals for InteliLite MRS16

Brands by name

Popular brands