ComAp InteliLite MRS16 Manual Download Page 14

Page: 14 / 632

InteliLite Global Guide

2.5.3 CM-GPRS

GSM/GPRS Internet module

Wireless integrated solution

Quick and easy installation

Support of WebSupervisor

Instant alarm SMS notification

System control over SMS

Quad Band GPRS/EDGE modem,

850/900/1800/1900 MHz

GPRS multi-slot class 10

TCP/IP communication over GPRS

2.5.4 CM-RS232-485

Communication module with two communication ports.

RS232 and RS485 interface

MODBUS, ECU link support

Serial connection to LiteEdit2015

2.5.5 EM-BIO8-EFCP

Hybrid current input and binary input/output extension module.

One additional AC current (CT) measuring for

Earth Fault Current protection (EFCP)

Wide range of measured current - one input for

1A and 1 input for 5A

Up to 8 additional configurable binary inputs or

outputs

Summary of Contents for InteliLite MRS16

























































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for InteliLite MRS16

Reviews:

Related manuals for InteliLite MRS16

Brands by name

Popular brands

ComAp InteliLite MRS16, Manual

Search results

Summary of Contents for InteliLite MRS16

Reviews:

Related manuals for InteliLite MRS16

Brands by name

Popular brands