manualshive.com logo in svg

ComAp InteliGen NT, Troubleshooting Manual, Page: 28 / 44

Share
Download
ComAp InteliGen NT Troubleshooting Manual Download Page 28

 

InteliGen

NT

, InteliSys

NT

, InteliMains

NT

 

– Troubleshooting Guide, 

SW version IGS-NT-3.1.0, IM-NT-3.1.0, ©ComAp 

– August 2018 

                28 

IGS-NT Troubleshooting Guide.pdf 

IGS-NT Alarm/History 

record

 

Alarm/ 

History 

Appeara

nce 

Description 

communication is OK.

 

AOUT 1-4

1

 

A+H 

Indication  of  error  in  communication  with  analog  outputs 
extension module.  
Check if the unit with corresponding CAN address is 

- 

powered up 

- 

address    of  the  module  is  set  correctly  (see 
Modules  card  in  GenConfig  and  an  extension 
module manual) 

- 

correctly  connected  and  check  connection  of 
terminating  resistors  on  the  CAN1  bus  (see  IGS-
NT Installation Guide, 

External 

modules 

connection

 chapter) 

- 

the CAN bus Low and High wires are not swapped 

To check module communication activity look at the Tx and 
Rx  LEDs  of  the  CAN  bus  port.  Fast  flashing  means  that 
communication is OK. 

ECU

1

 

A+H 

Indication of error in communication with ECU.  
Check if the ECU is: 

- 

correctly  connected  to  the  CAN1  port  of  the 
controller (see Comap Electronic Engines  Support 
manual for information about ECU connection) 

- 

powered up 

- 

terminating resistors are properly connected 

- 

the CAN bus Low and High wires are not swapped 

SHBIN 1-4

1

 

A+H 

Indication  of  error  in  communication  with  SHBOUT  1

–4 

module. 
Check that  

- 

one  of  the  controllers  on  site  is  configured  as  a 
SOURCE  controller  (has  SHBOUT  (x)  module 
configured) 

- 

the SOURCE controller is powered up 

- 

TARGET  and  SOURCE  controllers  are  connected 
to the CAN2 bus and Tx and Rx LEDs of the CAN2 
bus ports are flashing 

- 

the  controllers  can  "see"  each  other 

–  check 

CAN16/CAN32 values on the Power management 
screen  (each  controller  is  indicated  by  1  on  the 
position given by its address) 

- 

CAN2  bus  connection  is  done  according  to  the 
IGS-NT-Installation 

Guide, 

Recommended 

CAN/RS485 connection

 chapter. 

SHAIN 1-4

1

 

A+H 

Indication  of  error  in  communication  with  SHAOUT  1

–4 

module. 
Check that  

- 

one  of  the  controllers  on  site  is  configured  as  a 
SOURCE  controller  (has  SHAOUT  (x)  module 
configured) 

- 

the SOURCE controller is powered up 

- 

TARGET  and  SOURCE  controllers  are  connected 
to the CAN2 bus and Tx and Rx LEDs of the CAN2 
bus ports are flashing 

- 

the  controllers  can  "see"  each  other 

–  check 

CAN16/CAN32 values on the Power management 
screen  (each  controller  is  indicated  by  1  on  the 
position given by its address) 

Summary of Contents for InteliGen NT













































Reviews:

No comments