manualshive.com logo in svg

ComAp InteliDrive Mobile, Global Manual

The ComAp InteliDrive Mobile is an advanced control product designed for efficient and reliable engine management. With its user-friendly interface, users can easily operate and monitor their equipment. For a comprehensive understanding of its features, download the Global Manual from manualshive.com for free, and unleash the full potential of your machine.

Share
Download
background image

ID-Mobile Global Guide

85

Setpoint group

Engine parameters

Related FW

2.6.0

Range [units]

0.0 .. 100.0 [%/s]

Default value

5

Step

0.1 %/s

Comm object

9984

Related applications

Config level

Standard

Setpoint visibility

Always

Description

Speed ramp for BI Speed Up/Down not for Analog input request.

BI Speed Ramp

6

back to List of setpoints

Setpoint group

Engine parameters

Related FW

2.6.0

Range [units]

0 .. 100 [%]

Default value

50

Step

1 % of Requested RPM range.

Comm object

10008

Related applications

Config level

Standard

Setpoint visibility

Always

Description

When Binary input Fire speed is closed the binary output Clutch connect opens and engine Requested RPM

is set to Engine params: FireAlarmSpeed value.

FireAlarmSpeed (AS only)

6

back to List of setpoints

Setpoint group

Engine parameters

Related FW

2.6.0

Range [units]

[ENABLED / DISABLED]

Default value

DISABLED

Step

Comm object

10098

Related applications

Config level

Standard

Setpoint visibility

Always

Description

ENABLED

Engine speed request is defined by Engine params: Local speed setpoint. The speed

request can be changed regardless on controller mode.

DISABLED

Requested speed is changed via Binary inputs Speed up, Speed down or via analog input

Requested RPM.

EnLocalSpeed

6

back to List of setpoints

Summary of Contents for InteliDrive Mobile






































































































































































































































































Reviews:

No comments

Related manuals for InteliDrive Mobile

D-Link DWC-2000 Cli Reference Manual preview
DWC-2000
Brand: D-Link Pages: 113
D-Link DWC-1000 Reference Manual preview
DWC-1000
Brand: D-Link Pages: 146
Panasonic Minas A4 Series Connection Manual preview
Minas A4 Series
Brand: Panasonic Pages: 5
DSE DSE 6120 Installation Instructions preview
DSE 6120
Brand: DSE Pages: 2
ICP DAS USA XP-9 88-IoT Series Quick Start Manual preview
XP-9 88-IoT Series
Brand: ICP DAS USA Pages: 8
ICON AIRFLOW PCM Manual preview
AIRFLOW PCM
Brand: ICON Pages: 2
ICP DAS USA SP-S2-DS Quick Start preview
SP-S2-DS
Brand: ICP DAS USA Pages: 4
S&P PDS CONTROL Series Manual preview
PDS CONTROL Series
Brand: S&P Pages: 32
Engineering Solutions ACCESSOR 4000+ Owner'S Manual preview
ACCESSOR 4000+
Brand: Engineering Solutions Pages: 34
Pepperl+Fuchs VBA-2E-G11-I/U/PT100-F Manual preview
VBA-2E-G11-I/U/PT100-F
Brand: Pepperl+Fuchs Pages: 24
Danfoss NovoCon S Digital Installation Manual preview
NovoCon S Digital
Brand: Danfoss Pages: 2
Cypress CY8C28 series Technical Reference Manual preview
CY8C28 series
Brand: Cypress Pages: 571
Conductrix Wampfler 0832 Installation Instructions Manual preview
0832
Brand: Conductrix Wampfler Pages: 23
Carel E2V Installation preview
E2V
Brand: Carel Pages: 2
Timotion TBB5 User Manual preview
TBB5
Brand: Timotion Pages: 9
Midland A-14167 Series Installation, Operation & Maintenance Manual preview
A-14167 Series
Brand: Midland Pages: 37
Sensitron ST.PL4+ Installation And User Manual preview
ST.PL4+
Brand: Sensitron Pages: 32
Sparkfun Electronics Explorer Dongle Manual preview
Explorer Dongle
Brand: Sparkfun Electronics Pages: 16

Brands by name

Popular brands

Load more brands