manualshive.com logo in svg

ComAp InteliDrive Mobile, Global Manual

The ComAp InteliDrive Mobile is an advanced control product designed for efficient and reliable engine management. With its user-friendly interface, users can easily operate and monitor their equipment. For a comprehensive understanding of its features, download the Global Manual from manualshive.com for free, and unleash the full potential of your machine.

Share
Download
background image

ID-Mobile Global Guide

23

Indication of RPM2 and RPM3 in

DriveMonitor-2.5

Indication of Engine RPM (RPM1 in

default).

2.6.5 Impulse inputs

Use active NPN open collector

sensors.

2.7 Jumpers – hardware configuration

Prior to configuration procedure the hardware jumpers has to be connected. See below available jumpers

groups.

Note:

Take care of correct jumper setting to avoid repeated ID Mobile box opening.

A GROUP

AOUT1-AOUT8 range switch

B GROUP

AOUT1-AOUT8 function and On/Off switch

C GROUP

AIN1 – AIN16 range switch

BOUT1-8

Corresponding jumper has to be closed when BOUT is not used (wired) to avoid

BW (broken wire) message.

CAN1, CAN2, RS485

Terminating 120 ohms resistors

SGO

Speed governor (analog) output selection

Summary of Contents for InteliDrive Mobile






































































































































































































































































Reviews:

No comments

Related manuals for InteliDrive Mobile

Echelon Excel 50 Installation Instructions Manual preview
Excel 50
Brand: Echelon Pages: 40
rada 566 Installation And Maintenance Manual preview
566
Brand: rada Pages: 16
Harmonic Drive CHA Engineering Data preview
CHA
Brand: Harmonic Drive Pages: 85
jablotron Oasis JA-80 Installation Manual preview
Oasis JA-80
Brand: jablotron Pages: 22
jablotron JA-113E Manual preview
JA-113E
Brand: jablotron Pages: 2
National Instruments PXI-6683 Series Installation Manual preview
PXI-6683 Series
Brand: National Instruments Pages: 4
National Instruments NI R Series User Manual preview
NI R Series
Brand: National Instruments Pages: 9
National Instruments NI 9474 Getting Started preview
NI 9474
Brand: National Instruments Pages: 11
National Instruments NI 9401 Operating Instructions And Specifications preview
NI 9401
Brand: National Instruments Pages: 29
National Instruments NI 9214 Manual preview
NI 9214
Brand: National Instruments Pages: 11
National Instruments NI-488.2 Getting Started preview
NI-488.2
Brand: National Instruments Pages: 7
National Instruments FIELDPOINT FP-1600 Quick Start Manual preview
FIELDPOINT FP-1600
Brand: National Instruments Pages: 21
National Instruments FieldPoint FP-1001 User Manual preview
FieldPoint FP-1001
Brand: National Instruments Pages: 65
National Instruments FieldPoint FP-1001 Quick Start Manual preview
FieldPoint FP-1001
Brand: National Instruments Pages: 19
National Instruments GPIB-SCSI-A Installation Manual preview
GPIB-SCSI-A
Brand: National Instruments Pages: 16
National Instruments NI 9209 Calibration Procedure preview
NI 9209
Brand: National Instruments Pages: 10
Watts 009 Series Operation, Installation, Maintenance And Repair Manual preview
009 Series
Brand: Watts Pages: 8
Yamaha disklavier DKC-850 Quick Start Manual preview
disklavier DKC-850
Brand: Yamaha Pages: 2

Brands by name

Popular brands

Load more brands