manualshive.com logo in svg

ComAp InteliDrive Mobile, Global Manual

The ComAp InteliDrive Mobile is an advanced control product designed for efficient and reliable engine management. With its user-friendly interface, users can easily operate and monitor their equipment. For a comprehensive understanding of its features, download the Global Manual from manualshive.com for free, and unleash the full potential of your machine.

Share
Download
background image

ID-Mobile Global Guide

157

Related FW

2.6.0

Related applications

AMF, MRS

Comm object

151

Description

Active input blocks protections that are configured as (in DriveConfig) as Property:Prot.block type= Force

Block. Corresponding setpoint is ForceBlock del.

Force Block

6

back to List of LBI

LBI: G

Related FW

2.6.0

Related applications

AMF, MRS

Comm object

218

Description

Ena/Disables the GeoFencing function (engine block and active alarm) when the

Geo Fencing (page 111)

=

BIN.INPUT.

GeoFencingEna

6

back to List of LBI

LBI: H

Related FW

2.6.0

Related applications

AMF, MRS

Comm object

219

Description

Active input (rising edge) moves the actual position into

Home Lat (page 109)

and

Home Long (page 110)

.

Home Position

6

back to List of LBI

Related FW

2.6.0

Related applications

AMF, MRS

Comm object

153

Description

Binary input Horn reset is edge sensing signal.

Horn Reset

6

back to List of LBI

LBI: L

Related FW

2.6.0

Related applications

AMF, MRS

Comm object

182

Description

“Load blocking” can block the LBO Close load. Active input is indicated in Alarm list as “Load blocking”

message.

Load Blocking

6

back to List of LBI

Summary of Contents for InteliDrive Mobile






































































































































































































































































Reviews:

No comments

Related manuals for InteliDrive Mobile

T-Verter E2 Series Operating Manual preview
E2 Series
Brand: T-Verter Pages: 121
Happy 1050 Installation & Use Instructions preview
1050
Brand: Happy Pages: 10
Raymarine P70 Quick Reference preview
P70
Brand: Raymarine Pages: 12
Jafar 2005 Operation And Maintenance Manual preview
2005
Brand: Jafar Pages: 13
Panasonic KT2 Communication Instruction Manual preview
KT2
Brand: Panasonic Pages: 12
Panasonic CZ-64ESMC1U Operating Instructions Manual preview
CZ-64ESMC1U
Brand: Panasonic Pages: 10
3Ware 7000-2 - Escalade RAID Controller Features preview
7000-2 - Escalade RAID Controller
Brand: 3Ware Pages: 2
4 Moms Origami 4M-006-01 Instruction Manual preview
Origami 4M-006-01
Brand: 4 Moms Pages: 28
Danfoss vlt soft starter mcd 500 Operating Instruction preview
vlt soft starter mcd 500
Brand: Danfoss Pages: 95
Danfoss EKE 347 Installation Manual preview
EKE 347
Brand: Danfoss Pages: 12
Danfoss VLT 5000 Instruction Manual preview
VLT 5000
Brand: Danfoss Pages: 33
Danfoss VLT 6000 Installation Manual preview
VLT 6000
Brand: Danfoss Pages: 59
Danfoss EKC 361 User Manual preview
EKC 361
Brand: Danfoss Pages: 16
Danfoss VLT AQUA Drive FC 200 Operating Instructions Manual preview
VLT AQUA Drive FC 200
Brand: Danfoss Pages: 91
Danfoss EvoFlat WSS Installation Manual preview
EvoFlat WSS
Brand: Danfoss Pages: 2
Danfoss FC 300 Operating Instructions Manual preview
FC 300
Brand: Danfoss Pages: 100
Danfoss FC 300 Operating Instruction preview
FC 300
Brand: Danfoss Pages: 82
Danfoss Optyma Plus User Manual preview
Optyma Plus
Brand: Danfoss Pages: 18

Brands by name

Popular brands

Load more brands