manualshive.com logo in svg

ComAp InteliDrive Mobile, Global Manual

The ComAp InteliDrive Mobile is an advanced control product designed for efficient and reliable engine management. With its user-friendly interface, users can easily operate and monitor their equipment. For a comprehensive understanding of its features, download the Global Manual from manualshive.com for free, and unleash the full potential of your machine.

Share
Download
background image

ID-Mobile Global Guide

102

Setpoint group

Act. Calls/SMS

Related FW

2.6.0

Range [units]

[DISABLED, ENABLED]

Default value

DISABLED

Step

Comm object

8484

Related applications

Config level

Standard

Setpoint visibility

Always

Description

Enables or disables active calls/SMS to selected phone or mobile numbers when a Shut down alarm occurs.

Shut Down Call

6

back to List of setpoints

Setpoint group

Act. Calls/SMS

Related FW

2.6.0

Range [units]

[DISABLED, ENABLED]

Default value

DISABLED

Step

Comm object

8485

Related applications

Config level

Standard

Setpoint visibility

Always

Description

Enables or disables active calls/SMS to selected phone or mobile numbers when a Cool down alarm occurs.

Cool Down Call

6

back to List of setpoints

Summary of Contents for InteliDrive Mobile






































































































































































































































































Reviews:

No comments

Related manuals for InteliDrive Mobile

Nelsen Corporation C Series Programming Manual preview
C Series
Brand: Nelsen Corporation Pages: 16
National Instruments C Series Getting Started preview
C Series
Brand: National Instruments Pages: 34
Panasonic FP2 Series Technical Manual preview
FP2 Series
Brand: Panasonic Pages: 68
Panasonic GP-KS162CUDE Operating Instruction preview
GP-KS162CUDE
Brand: Panasonic Pages: 27
Panasonic EBL512 G3 5000 Planning Instructions preview
EBL512 G3 5000
Brand: Panasonic Pages: 168
Panasonic WV-CU980 Software Update Procedure preview
WV-CU980
Brand: Panasonic Pages: 8
Panasonic AW-RP50 Manual preview
AW-RP50
Brand: Panasonic Pages: 3
Panasonic FP0H Series Operation Manual preview
FP0H Series
Brand: Panasonic Pages: 20
Panasonic AK-HRP1010G Operating Manual preview
AK-HRP1010G
Brand: Panasonic Pages: 29
Panasonic AK-HRP1005G Operation Manual preview
AK-HRP1005G
Brand: Panasonic Pages: 37
Panasonic AG-EC4G Operating Instructions Manual preview
AG-EC4G
Brand: Panasonic Pages: 9
Jeep Liberty Instruction Sheet preview
Liberty
Brand: Jeep Pages: 32
Accel 300+ Installation Instructions Manual preview
300+
Brand: Accel Pages: 8
D+H RZN 4503-T Instructions For Use Manual preview
RZN 4503-T
Brand: D+H Pages: 14
GAC ESD-5550 Series Technical Information preview
ESD-5550 Series
Brand: GAC Pages: 12
M-Audio Axiom AIR 25 Service Manual preview
Axiom AIR 25
Brand: M-Audio Pages: 26
M Climate Bobbie Installation Instructions Manual preview
Bobbie
Brand: M Climate Pages: 12
Uniden UBC-RH96 Owner'S Manual preview
UBC-RH96
Brand: Uniden Pages: 28

Brands by name

Popular brands

Load more brands