ComAp InteliDrive FLX LITE Manual Download Page 128

Page: 128 / 228

ID-FLX Lite Global Guide

128

Setpoint group

Engine parameters

Related FW

2.5.0

Range [units]

0 .. 1000 [min]

Default value

Step

Comm object

11837

Related applications

Description

Automatic engine stop in MAN mode or delayed engine stop in AUT mode. Start engine in MAN mode by

START button. Engine stops itself after Running Timer is over. Engine stays running when

Running timer

(page 128)

= 0

Running timer

back to List of setpoints

Setpoint group

Engine parameters

Related FW

2.5.0

Range [units]

0 .. 10000 [L]

Default value

200

Step

Comm object

11103

Related applications

Description

This setpoint is describing volume of fuel tank for counting fuel consumption depending on Fuel level drop.

FuelTankVolume

back to List of setpoints

Setpoint group

Engine parameters

Related FW

2.5.0

Range [units]

0 .. 50 [%/h]

Default value

Step

Comm object

12373

Related applications

Description

This is setting protection against the fuel leakage or theft.

Function monitors the AIN3 Fuel level value in percentage scale without decimals. The alarm and history

record “Wrn FuelTheft” is activated when Fuel level change is faster than setpoint limit. Function is switched

off when Max Fuel Drop = 0 %/h.

The drop out limit on stopped engine is 5% to avoid unwanted Alarm activation due to AIN3: Fuel level

fluctuations.

Active alarm "Wrn FuelTheft" can be sent via SMS and displayed by WebSupervisor (if used).

Note:

Set 0 to disable Fuel Theft Protection function into MaxFuelDrop setpoint.

MaxFuelDrop

back to List of setpoints

Summary of Contents for InteliDrive FLX LITE





































































































































































































































Search results

Summary of Contents for InteliDrive FLX LITE

Reviews:

ComAp InteliDrive FLX LITE, Manual, Page: 128 / 228

Search results

Summary of Contents for InteliDrive FLX LITE

Reviews: