ComAp InteliDrive DCU Marine Manual Download

Page: 5 / 285

InteliDrive DCU Marine - 3.0.0 Global Guide

1 Document information

1.1 Clarification of notation

1.2 About this guide

1.3 Legal notice

1.1 Clarification of notation

Note:

This type of paragraph calls readers attention to a notice or related theme.

IMPORTANT: This type of paragraph highlights a procedure, adjustment etc., which can cause a

damage or improper function of the equipment if not performed correctly and may not be clear at

first sight.

Example:

This type of paragraph contains information that is used to illustrate how a specific function

works.

1.2 About this guide

InteliDrive DCU Marine is a specialized engine controller for Marine applications. It controls, monitors and

protects the engine in single (Auxiliary) or variable (propulsion) speed operational modes. The controller can

communicate with Engine Management System via the CAN serial line using standard J1939 or another

(KWP2000) communication protocol.

InteliDrive controllers are equipped with a powerful graphic display with icons, symbols and bar-graphs for

intuitive operation, which together with high functionality sets new standards in engine controls.

Engine functions

Engine sequencing and control (start/stop, warm-up and cool-down, pre-lubrication etc.)

Engine monitoring and protections (2 or more level analog inputs protection, adjustable delays)

Speed measurement from magnetic pick-up or from ECU

Running hours meter, number of starts counter

Configurable 14 Binary inputs and Outputs and 8 Analog inputs

Setpoints are adjustable via InteliDrive panel or via PC software

3 level password protection

On screen Alarm and ECU Alarm indication

Event and time driven engine history for back tracing

Two or more languages selectable in controller

Communication

RS232 / Modbus RTU

Analog or GSM modem

Internet

Summary of Contents for InteliDrive DCU Marine






























































































































































































































































































Search results

Summary of Contents for InteliDrive DCU Marine

Reviews:

Related manuals for InteliDrive DCU Marine

Brands by name

Popular brands

ComAp InteliDrive DCU Marine, Manual

Search results

Summary of Contents for InteliDrive DCU Marine

Reviews:

Related manuals for InteliDrive DCU Marine

Brands by name

Popular brands