ComAp InteliDrive DCU Marine Manual Download

Page: 31 / 285

InteliDrive DCU Marine - 3.0.0 Global Guide

Combined - Harbour mode (CMB archive)

ID-DCU MARINE can be switched to

EME

HRB

mode by ID-DCU MARINE Mode panel buttons.

EME mode behavior is like above.

In HRB mode the controller operates lik e in AUX mode (all engine protections are active) but message

“HARBOUR MODE” in Alarm list and Binary outputs HRB mode and binary output Common Alarm is active.

Controller starts and stops the engine according to the binary inputs Blackout Start or Remote Start, Rem

Start/Stop, Remote Stop or to the ID-DCU MARINE Start / Stop buttons. Binary inputs Blackout Start and

Remote Start and Remote Stop are inactive in LOC (Local) mode.

Propulsion mode (PRP archive)

PRP mode is designed for multiple propulsion engines with variable speed

Controller starts and stops the engine according to the binary inputs RemRepStart or Remote Start, Rem

Start/Stop, Remote Stop or to the ID-DCU MARINE Start / Stop buttons. Binary inputs RemRepStart and

Remote Start and Remote Stop are inactive in LOC (Local) mode.

All engine protections and all configured shutdown protections are active. Controller continuously monitors

all available engine parameters (oil pressure, water temperature, RPM, fuel level etc.). The engine will stop

and activates Common Warning and Common Shutdown outputs and writes record to the history file when

detects any active Shut down alarm. This condition can be signaled by Active call feature to remote operator

via modem, SMS or e-mail.

Other functions

Controller (except OFF mode) accepts when engine is started outside controller (by hand) or when controller

power supply is switched-on on already running engine.

3.1.4 Universal states

State is a value joined to each Analog input or value. State indicates if any protection configured on

corresponding analog input is active or not. When there is any state configured as protection the corresponding

Binary output appears in Analog protection list and can be used for selective external indication of the Alarm.

State is resetted (output is opened) when corresponding Alarm is not active and confirmed (Fault reset was

pressed).

There are seven universal (free) states available in ID-DCU MARINE-3.0.0 that are not joined to any value or

input.

Summary of Contents for InteliDrive DCU Marine






























































































































































































































































































Search results

Summary of Contents for InteliDrive DCU Marine

Reviews:

Related manuals for InteliDrive DCU Marine

Brands by name

Popular brands

ComAp InteliDrive DCU Marine, Manual

Search results

Summary of Contents for InteliDrive DCU Marine

Reviews:

Related manuals for InteliDrive DCU Marine

Brands by name

Popular brands