ComAp InteliDrive DCU Marine Manual Download

Page: 211 / 285

InteliDrive DCU Marine - 3.0.0 Global Guide

211

Related FW

3.0.0

Related applications

All

Comm object

280

Description

Indicates Ready state for Remote engine start.

RdyForRemStart

back to List of LBO

Related FW

3.0.0

Related applications

All

Comm object

116

Description

The output closes at the beginning of prestart and opens if the engine shall be stopped.This output can be

used to indicate when the ECU should be powered up i.e. only while the engine is running.

This output also influences evaluation of communication failure with ECU and related FLS alarms from

analog inputs read from the ECU. If the output is configured (which means configured on physical binary

output or VBOUT output), the issuing of communication error is blocked during Prestart and Stopping

procedure as shown in the picture.

Note:

The input must be configured on physical binary output or VBOUT output. It is not enough to

configure it as a PLC input for example.

ECU PowerRelay

back to List of LBO

Related FW

3.0.0

Related applications

All

Comm object

281

Description

1 sec pulse is generated after panel Start button is pressed.

StartButtEcho

back to List of LBO

Summary of Contents for InteliDrive DCU Marine






























































































































































































































































































Search results

Summary of Contents for InteliDrive DCU Marine

Reviews:

Related manuals for InteliDrive DCU Marine

Brands by name

Popular brands

ComAp InteliDrive DCU Marine, Manual

Search results

Summary of Contents for InteliDrive DCU Marine

Reviews:

Related manuals for InteliDrive DCU Marine

Brands by name

Popular brands