ComAp InteliDrive DCU Marine Manual Download

Page: 144 / 285

InteliDrive DCU Marine - 3.0.0 Global Guide

144

RPMdep protect (PRP only)

RPM dependent Oil pressure and Coolant pressure protections are available in PRP (propulsion) application

only. Both protections are by default set to Protection block type = RunOnlyBlkDel1 (Engine running - block

delay 1).

There are two setpoints for linear Warning limit, two for Shutdown limit and one for delay. Setpoints adjusting

step and range depends on corresponding sensor characteristics.

Note:

The particular RPM dependent protection is fully disabled if both xxxIdlexxx and xxxNomxxx parameters

are set to value 0,0. I.e. the protection is not activated even if measured value is negative (e.g. when there is a

wrong sensor calibration).

Setpoint group

RPMdep Protect

Related FW

3.0.0

Range [units]

0,0 .. 10,0 [Bar]

Default value

0,0

Step

0,1

Comm object

10140

Related applications

PRP

Config level

Standard

Setpoint visibility

Always

Description

Linear Warning characteristic is defined by two points for

Idle RPM

and

Nominal RPM

.OPIdleRPMWrn

defines oil pressure warning level at idle speed.

OPIdleRPMWrn

back to List of setpoints

Summary of Contents for InteliDrive DCU Marine






























































































































































































































































































Search results

Summary of Contents for InteliDrive DCU Marine

Reviews:

Related manuals for InteliDrive DCU Marine

Brands by name

Popular brands

ComAp InteliDrive DCU Marine, Manual

Search results

Summary of Contents for InteliDrive DCU Marine

Reviews:

Related manuals for InteliDrive DCU Marine

Brands by name

Popular brands