ComAp InteliDrive DCU Marine Manual Download

Page: 14 / 285

InteliDrive DCU Marine - 3.0.0 Global Guide

Param fail

Setpoints checksum fail

RTC battery

RTC battery fail

System

Controller system related record

TimeModeChange

Winter/Summer time change

Overload

Engine overload

OthrCommEr

Intercontroller communication error

Battery Flat

Controller reset during cranking

OP RPMdep

Out of Oil pressure RPM dependent limit indication

CP RPMdep

Out of Cooling pressure RPM dependent limit indication

Battery A volt

Battery A voltage of RPU is out of limits

Battery B volt

Battery B voltage of RPU is out of limits

Close Load ON

Close Load output is closed

Close Load OFF

Close Load output is opened

SwitchToBatt B

ID-RPU power supply switched to battery B

SdOverride ON

Sd Override function activated

SdOverride OFF

Sd Override function deactivated

Note:

Value name can’t exceed 11 characters to be recorded to History file with prefix (Wrn, Fls etc.). Longer

names characters are canceled.

Corresponding Sd BINx, Sd BOUTx or Sd AINx is indicated in Alarm list and history record when

communication with any extension units (IS-BIN, IS-AIN, IGS-PTM) is interrupted.

Example:

When IS-BIN16/8 is configured for addresses: Binary inputs = BIN1, BIN2 and Binary outputs =

BOUT1, then three messages Sd BIN1, Sd BIN2, Sd BOUT1 are indicated after communication is

interrupted.

Note:

Any “State” information can be configured to any binary output by DriveConfig software.

2.1.2 Display menu

There are 4 display menus available: MEASUREMENT, External measurement, ADJUSTMENT and

HISTORY.

Each menu consists of several screens. Pressing the Page button repeatedly will scroll the user through the

menu screens.

Summary of Contents for InteliDrive DCU Marine






























































































































































































































































































Search results

Summary of Contents for InteliDrive DCU Marine

Reviews:

Related manuals for InteliDrive DCU Marine

Brands by name

Popular brands

ComAp InteliDrive DCU Marine, Manual

Search results

Summary of Contents for InteliDrive DCU Marine

Reviews:

Related manuals for InteliDrive DCU Marine

Brands by name

Popular brands