manualshive.com logo in svg

ComAp InteliDrive DCU Marine, Manual

The ComAp InteliDrive DCU Marine is a cutting-edge control unit designed for marine applications. Access its comprehensive functionality with ease by downloading the user-friendly Reference Manual from our website, available for free. Empower your marine operations with this exceptional product from ComAp.

Share
Download
background image

InteliDrive DCU Marine - 3.0.0 Global Guide

133

Setpoint group

Engine params

Related FW

3.0.0

Range [units]

0,0 .. 100,0 [%]

Default value

0,0

Step

0,1

Comm object

9948

Related applications

All

Config level

Standard

Setpoint visibility

Always

Description

Setpoint specifies

Engine Values: Speed Request

when

Engine params: EnLocalSpeed =

ENABLED

. Setpoint can be changed as standard setpoint or by Fast edit function: press Enter for 4 sec,

/ ¯ set value, press Enter to confirm. see

Speed Request (page 266)

charts for PRP and AUX / EME / HRB modes.

Local Speed

6

back to List of setpoints

Summary of Contents for InteliDrive DCU Marine






























































































































































































































































































Reviews:

No comments

Related manuals for InteliDrive DCU Marine

Baby Jogger City Single Assembly Instructions Manual preview
City Single
Brand: Baby Jogger Pages: 16
Wavelink Avalanche User Manual preview
Avalanche
Brand: Wavelink Pages: 69
Gatekeeper ITSS User Manual & Install Manual preview
ITSS
Brand: Gatekeeper Pages: 28
Lamtec BT300 BurnerTronic Quick Reference preview
BT300 BurnerTronic
Brand: Lamtec Pages: 48
L-Acoustics LA8 Product Information preview
LA8
Brand: L-Acoustics Pages: 20
Osram OT EASY 32 CC Fitting Instructions preview
OT EASY 32 CC
Brand: Osram Pages: 3
WAGNER 2K COMFORT Original Operating Manual preview
2K COMFORT
Brand: WAGNER Pages: 128
Fibocom SU806-LA Hardware Manual preview
SU806-LA
Brand: Fibocom Pages: 79
oventrop Multidis SFQ Operating Instructions Manual preview
Multidis SFQ
Brand: oventrop Pages: 40
REGLOPLAS 90M Operating Instructions Manual preview
90M
Brand: REGLOPLAS Pages: 44
Sentiotec CV 4 Installation And Operating Instructions Manual preview
CV 4
Brand: Sentiotec Pages: 45
Invertek Optidrive Elevator Quick Start Up Manual preview
Optidrive Elevator
Brand: Invertek Pages: 5
Techtrol TLIC Instruction And Programming Manual preview
TLIC
Brand: Techtrol Pages: 4
Grundfos PLV Series Installation And Operating Instructions Manual preview
PLV Series
Brand: Grundfos Pages: 16
Loewe 70830 081 Installation Instructions Manual preview
70830 081
Brand: Loewe Pages: 62
Shimaden PAC18A Series Instruction Manual preview
PAC18A Series
Brand: Shimaden Pages: 32
Beckhoff CX2550 Series Manual preview
CX2550 Series
Brand: Beckhoff Pages: 30
Festo CPS-Gate Operating Instructions Manual preview
CPS-Gate
Brand: Festo Pages: 109

Brands by name

Popular brands

Load more brands