ComAp InteliDrive DCU Marine Manual Download

Page: 118 / 285

InteliDrive DCU Marine - 3.0.0 Global Guide

118

Setpoint group

Comms Settings

Related FW

3.0.0

Range [units]

1 .. 32 [-]

Default value

Step

Comm object

24537

Related applications

All

Config level

Standard

Setpoint visibility

Always

Description

Controller identification number. Each controller in the group has to have its own unique number. Default

value is 1.

Note:

The InteliDrive

ControllerAddr

must correspond to InteliMonitor or DriveConfig communication

setup setting when opening Direct or Modem connection.

ControllerAddr

back to List of setpoints

Setpoint group

Comms Settings

Related FW

3.0.0

Range [units]

[ENABLED, DISABLED, EXTERNAL]

Default value

ENABLED

Step

[-]

Comm object

10353

Related applications

All

Config level

Standard

Setpoint visibility

Always

Description

This setpoint is used to disable reading of diagnostic codes from ECU if an external diagnostic tool is

connected to engine.

Message ECU Diag disabled is displayed in the alarm list while ECU diagnostics is disabled.

The ECU Diagnostic is disabled/enabled using LBI:

ECU DiagBlck

binary input in case of setting to

EXTERNAL.

ECU Diag

back to List of setpoints

Summary of Contents for InteliDrive DCU Marine






























































































































































































































































































Search results

Summary of Contents for InteliDrive DCU Marine

Reviews:

Related manuals for InteliDrive DCU Marine

Brands by name

Popular brands

ComAp InteliDrive DCU Marine, Manual

Search results

Summary of Contents for InteliDrive DCU Marine

Reviews:

Related manuals for InteliDrive DCU Marine

Brands by name

Popular brands