ComAp InteliDrive DCU Industrial Global Manual Download

Page: 30 / 350

InteliDrive DCU Industrial 3.4.0 Global Guide

4 Installation and wiring

4.1 Terminal and dimensions

4.2 Recommended wiring

4.3 Getting started

back to Table of contents

4.1 Terminal and dimensions

4.1.1 ID-DCU Industrial

The front panel of the InteliDrive controller is intended for installation in an overall enclosure – rubber seal for IP

65 -

Technical data (page 93)

Left RED

Active alarm indication

Blinks when new alarm is activated.

Steady lights after "Fault reset" confirmation - when

alarm is still active.

Disappears after "Fault reset" confirmation.- when alarm

is inactive.

Right GREEN

Engine running indication

Light when engine is running.

Front panel LED

Note:

Please check the last software version.

Summary of Contents for InteliDrive DCU Industrial































































































































































































































































































































































Search results

Summary of Contents for InteliDrive DCU Industrial

Reviews:

Related manuals for InteliDrive DCU Industrial

Brands by name

Popular brands

ComAp InteliDrive DCU Industrial, Global Manual

Search results

Summary of Contents for InteliDrive DCU Industrial

Reviews:

Related manuals for InteliDrive DCU Industrial

Brands by name

Popular brands