ComAp IG-NT GC Reference Manual Download | Manualshive

Page: 251 / 260

background image

IGS-NT-BC, SW Version 1.2.0,

©ComAp – January 2019

IGS-NT-BC-1.2.0 Reference Guide.PDF

251

be generated from the moment of button pushing.

Binary output: RemoteControl1

Related FW

3.0

Description

This is a general purpose output, which can be closed and opened remotely, e.g.
from InteliMonitor using the "Remote switches" tool or via MODBUS using the
register #46361 and command #26.

N

OTE

:

See the

Remote switches

chapter in the InteliMonitor help for details about how to

control the output from InteliMonitor and the Modbus chapter in the latest
communication guide for information about control the output using Modbus.

Binary output: RemoteControl2

Related FW

3.0

Description

This is a general purpose output, which can be closed and opened remotely, e.g.
from InteliMonitor using the "Remote switches" tool or via MODBUS using the
register #46361 and command #26.

N

OTE

:

See the

Remote switches

chapter in the InteliMonitor help for details about how to

control the output from InteliMonitor and the Modbus chapter in the latest
communication guide for information about control the output using Modbus.

Binary output: RemoteControl3

Related FW

3.0

Description

This is a general purpose output, which can be closed and opened remotely, e.g.
from InteliMonitor using the "Remote switches" tool or via MODBUS using the
register #46361 and command #26.

N

OTE

:

See the

Remote switches

chapter in the InteliMonitor help for details about how to

control the output from InteliMonitor and the Modbus chapter in the latest
communication guide for information about control the output using Modbus.

Binary output: RemoteControl4

Related FW

3.0

Description

This is a general purpose output, which can be closed and opened remotely, e.g.
from InteliMonitor using the "Remote switches" tool or via MODBUS using the
register #46361 and command #26.

N

OTE

:

See the

Remote switches

chapter in the InteliMonitor help for details about how to

control the output from InteliMonitor and the Modbus chapter in the latest
communication guide for information about control the output using Modbus.

«
...
249
250
251
252
253
...
»

Summary of Contents for IG-NT GC





































































































































































































































































Reviews:

No comments

Related manuals for IG-NT GC

FEPL-02 Ethernet POWERLINK

Brand: ABB Pages: 2

Brand: ABB Pages: 2

FPBA-01 PROFIBUS DP

Brand: ABB Pages: 2

ControlMaster CM15

Brand: ABB Pages: 4

Brand: Dahua Pages: 58

Brand: IDTECK Pages: 94

Brand: PACH & COMPANY Pages: 4

Slim Remote Control

Brand: Packard Bell Pages: 2

Brand: Unipower Pages: 24

Brand: Vaillant Pages: 32

Brand: Vaillant Pages: 27

Brand: Vaillant Pages: 40

Brand: Vaillant Pages: 36

Brand: Vaillant Pages: 28

Brand: Vaillant Pages: 92

Brand: Xilinx Pages: 52

Brand: Burlington Pages: 7

Brand: Seiko Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands