COMAC ANTEA 50 B, Use And Maintenance Manual

Page: 34 / 44

CAUTION
: these operations must be carried out using protective gloves to avoid any possible
contact with the edges or tips of metal objects.
4. Remove the vacuum hose (3) from the vacuum nozzle (4) on the squeegee body ( Fig. 3 ).
5. Remove the vacuum tube (3) from the hole on the back of the recovery tank ( Fig. 4 ).
6. Remove the recovery tank drainage hose from the clamps.
7. Remove the spray gun kit from the storage compartment ( Fig. 5 ).
8. Connect the male quick-coupler (5) on the spiral hose (6) to the female quick-coupler (7) on the front
of the appliance ( Fig. 6 ).
9. Connect the male quick-coupler (8) on the spray gun (9) to the female quick-coupler (10) on spiral
hose (6) ( Fig. 7 ).
10. Activate the spray gun kit by pressing the button (11) on the steering column ( Fig. 8 ).
CAUTION : when using the optional tank cleaning kit, you are advised to always wear goggles to
avoid any risk of serious injury to your eyes.
N.B. : Before activating the optional tank cleaning kit, check the level indicator (12) to see how
much solution there is in the solution tank (
Fig. 9
).
11. Start the delivery of detergent jet by pressing the lever (13) on the spray gun ( Fig. 10 ).
N.B. : To adjust the solution jet coming out of the spray gun turn the knob (14) on the accessory
itself ( Fig. 11 ).
12. Clean the inside of the vacuum hose with a jet of solution.
13. Repeat the operations in reverse order to reassemble all the parts.
N.B.
: the place designated for this operation must comply with current environmental protection
regulations.
N.B. : Pay particular attention when placing the vacuum hose behind the lifting chain, as indicated
on the label ( Fig. 12 ).
1
1
2
2
3
4
3
5 6
3
4
6
5
7
7 8
12
9
10 11
8
9
13
14
10 11
12
EMPTYING THE SOLUTION TANK
Proceed as follows to empty the solution tank:
1. Take the device to the dedicated maintenance area.
2. Take all necessary steps to ensure that the device is in a safe condition (see “ MACHINE SAFETY ”).
N.B.
: The tanks should be emptied in the place used for draining dirty water.
N.B. : the place designated for this operation must comply with current environmental protection
regulations.
CAUTION : users are advised to always wear protective gloves, to avoid the risk of serious injury
to hands.
3. Unscrew the detergent solution cap-filter (1), turning it counter-clockwise ( Fig. 1 ).
4. Repeat the operations in reverse order to reassemble all the parts.
1
1
CLEANING THE WATER SYSTEM FILTER
A thorough cleaning of the solution tank filter guarantees a longer life span of the appliance's water
circuit system, ensuring a better floor cleaning performance. Proceed as follows to clean the solution
tank's cap-filter:
1. Take the device to the dedicated maintenance area.
2. Take all necessary steps to ensure that the device is in a safe condition (see “ MACHINE SAFETY ”).
3. Make sure the solution tank is empty. If it isn't, empty it (see paragraph “ EMPTYING THE SOLUTION
TANK ”).
N.B.
: The tanks should be emptied in the place used for draining dirty water.
N.B. : the place designated for this operation must comply with current environmental protection
regulations.
CAUTION : users are advised to always wear protective gloves, to avoid the risk of serious injury
to hands.
4. Unscrew the detergent solution cap-filter (1), turning it counter-clockwise ( Fig. 1 ).
5. Clean it under a jet of clean water. Remove any impurities that may be present.
6. Repeat the operations in reverse order to reassemble all the parts.
1
1
CLEANING THE WATER SYSTEM (B versions)
Prior to any extended periods of disuse, do the following:
1. Take the device to the dedicated maintenance area.
2. Take all necessary steps to ensure that the device is in a safe condition (see “ MACHINE SAFETY ”).
N.B. : users are advised to always wear protective gloves, to avoid the risk of serious injury to
hands.
N.B. : the place designated for this operation must comply with current environmental protection
regulations.
3. Make sure the recovery tank is empty, otherwise empty it completely (read the paragraph“ EMPTYING
THE RECOVERY TANK ”).
4. Verify that the quantity of detergent solution in the solution tank is suitable for the type of work you
wish to carry out, otherwise fill the solution tank (see the paragraph “ FILLING THE SOLUTION TANK
WITH WATER ”). View the level tube (1) in the rear of the machine ( Fig. 1 ).
5. Grip the handle (1) on the left side of the recovery tank ( Fig. 2 ) and turn the tank as far as it will go,
until it reaches the maintenance position (
Fig. 3
).
6. Connect the battery connector (3) to the main system connector (2) ( Fig. 4 ).
ATTENTION: This process must be carried out by qualified personnel.
7. Grip the handle (2) on the side of the recovery tank ( Fig. 5 ).
8. Turn the recovery tank as far as it will go, to the work position ( Fig. 6 ).
9. Make sure the water tap is fully open; the water adjustment knob (4) should be completely down
( Fig. 7 ).
10. Press the main system control button (5) so it is in the “work” position ( Fig. 8 ).
N.B. : when the main system control button is functioning, the LED inside it is activated.
11. Lower the brush head unit by pressing the brush head control pedal (6) on the back of the appliance
( Fig. 9 ).
N.B. : Do not bring the brush completely into contact with the floor.
1
1
3
2
2
4
3
2
2
6 5
7
4
5
8
ON
6
9
34