background image

 

Page 9 of 10

 

INSTRUCTION MANUAL 

 

Preamplifier Model PAM-103 

 

1 9 1 2 1   E l   T o r o   R d     ●     S i l v er a d o ,   C a l i f o r n i a   9 2 6 7 6     ●    ( 9 4 9 )   4 5 9 -9 6 0 0     ●    

c o m - p o w e r . c o m

 

                                                                                                                                                                                 REV012017 

5.4 Battery Replacement and troubleshooting tips 

The replaceable battery pack can be accessed from the bottom of the preamplifier. Four screws 
secure the cover to the battery compartment. Please charge the new batteries overnight initially 
to maximize operating time of the preamplifier. 
 

 

 

5.5 Troubleshooting Common problems 

 

Problem: Gain is low or no gain. 

 

A: Make sure the power switch is on and the green is LED is lit. 

 
Check if the input and output cables are connected securely. Wiggle both cables and verify if the 
signal level changes on the receiver. If the signal changes replace the defective cable and check 
again. Make sure the cable from the signal source is connected to the input not the output.  
 
Verify if the signal source connected.  If it is a signal generator make sure the RF is turned on.   
 
Inject a known signal level into the preamplifier and check the gain. For example if you inject 50 
dBµV, you should read ~ 81 to 83 dBµV on the receiver. Please be cautious not to exceed the 
input limits given in specification table of this manual. 
 
Make sure the battery is fully charged or the adapter is plugged into a AC power source. 
 
 

Problem: Battery low indicator remains lit even after charging overnight. 

 

A:

 The battery may need to be replaced. However, before you replace the battery perform the 

following steps 

 

Make sure the battery terminals are connected to the preamplifier  

 

Check the fuse on the back panel. If the fuse is blown, replace it. Please heed 
the warning label on the bottom of the fuse holder and rear panel. 

 

Check the charging adapter to make sure it is supplying the rated voltage on the 
adapter. If the charging adapter is producing the proper voltage, the batteries 
may have to be replaced. Otherwise replace the charger adapter.

 

 

 

Summary of Contents for PAM-103











Reviews: