Columbia HERITAGE series Installation, Operating And Service Instructions Download Page 15

15

VII. System Start-up and Checkout

A

.

  

Main Burner Check

 - Check main burners to see 

that they were not dislodged during shipment. Rear 

of burners should be in the vertical slots in the rear of 

burner tray and the front of the burners should be seated 

completely on the orifices.

B.

 

Initial start

 -

1. 

Fill entire heating system with water

 and vent 

air from system. Use the following procedure on a 

System equipped with zone valves.
a.  Close isolation valve in boiler supply piping.
b.  Isolate all circuits by closing zone valves or 

balancing valves.

c.  Attach a hose to hose bib located just below 

isolation valve in boiler supply piping. (Note 

- Terminate hose in five gallon bucket, at a 

suitable floor drain, or outdoor area).

d.  Starting with one circuit, open zone valve.
e.  Open hose bib.

f.  Open fill valve (Make-up water line should be 

located directly above isolation valve in boiler 

supply piping).

g.  Allow water to overflow from bucket until 

discharge from hose is bubble free for 30 

seconds.

h.  Open zone valve to the second zone to be 

purged, then close the first.  Repeat this step until 

all zones have been purged, but always have one 

zone open.  At completion, open all zone valves.

i.  Close hose bib, continue filling the system 

until the pressure gauge reads 12 psi.  Close fill 

valve.  (Note - If make-up water line is equipped 

with pressure reducing valve, system will 

automatically fill to 12 psi.  Leave globe valve 

open).

j.  Open isolation valve in boiler supply piping.
k.  Remove hose from hose bib.

2. Turn ROOM THERMOSTAT to lowest setting.
3.  Be sure that gas to pilot and main burners has been 

off for at least five minutes and vent damper has 

been in the open position.

4.  Turn "OFF" the electric switch serving boiler.
5.  Open valve on main gas line at meter.
6.  PURGE AIR FROM GAS PIPING. A

dequate 

ventilation must be provided and no smoking or 

open flame permitted.

  

7.  Turn "ON" electric switch serving boiler.
8.

 

 Open Manual Shut-off Valve upstream of 

Combination Gas Valve.

9.  Loosen or remove Inlet Pressure Tap Plug in 

Combination Gas Valve and when purging is 

complete, tighten or replace plug. (See Figure 10).

Figure 10:  Top View of Honeywell Gas Valves

10.  Check pipe and fittings from meter to Combination 

Gas Valve using soap solution or other approved 

methods.

CAUTION

11.   Test gas piping and connections between 

Combination Gas Valve and manifold, orifices, and 

pilot piping for leaks after boiler is operating.  Use 

soap solution or other approved method.

C.

  

Check Gas Input to Boiler

1.  Input Rate and Maximum Inlet Pressure shown on 

Rating Label must not be exceeded.  Inlet pressure 

must not be lower than minimum inlet pressure 

shown on Rating Label.

2.  All Rate checks and all adjustments are to be made 

while boiler is firing - all other appliances connected 

to the same meter as the boiler must be off. 

3.  With boiler off, water Manometer or water column 

gauge should be connected to a shut-off valve 

installed in the 1/8" outlet pressure tap in the gas 

valve (See Figure 10).  By installing gas valve 

upstream of manometer, gas pressure can be 

introduced gradually - without shut-off valve; surge 

of pressure when boiler is turned on, could blow 

liquid out of manometer. Replace plug in gas valve 

when rate check is finished.

4.  LP Gas Input:
  Adjust Regulator on Gas Valve so that manifold 

pressure is 10 inches water column. Turning 

Regulator Adjusting Screw Clockwise increases 

pressure. Counterclockwise rotation decreases 

pressure.

Summary of Contents for HERITAGE series

































Reviews: