Colorado time systems MS-0043, User Manual

Page: 10 / 14

6 Deck Clock
DIP switch settings (Off = 0, On = 1)
Module : Switches 1-5 of S1 . 01 to 1E are valid.
0 0 0 1 0 08 0 0 0 0 1 10 0 0 0 1 1 18
1 0 0 0 0 01 1 0 0 1 0 09 1 0 0 0 1 11 1 0 0 1 1 19
0 1 0 0 0 02 0 1 0 1 0 0A 0 1 0 0 1 12 0 1 0 1 1 1A
1 1 0 0 0 03 1 1 0 1 0 0B 1 1 0 0 1 13 1 1 0 1 1 1B
0 0 1 0 0 04 0 0 1 1 0 0C 0 0 1 0 1 14 0 0 1 1 1 1C
1 0 1 0 0 05 1 0 1 1 0 0D 1 0 1 0 1 15 1 0 1 1 1 1D
0 1 1 0 0 06 0 1 1 1 0 0E 0 1 1 0 1 16 0 1 1 1 1 1E
1 1 1 0 0 07 1 1 1 1 0 0F 1 1 1 0 1 17 1 1 1 1 1 1F (this is test mode)
NOTE: switches 6-8 of S1, next to the Module switches, should not be changed.
Doing so will cause the display to cease functioning properly.
Channels: Switches 1-4 of S2 . 0 to 11 are valid
PAN ID: Switches 5-8 of S2 . 0 to 15 are valid
0 0 0 0 0 0 0 1 0 4 0 0 0 1 8 0 0 1 1 12
1 0 0 0 1 1 0 1 0 5 1 0 0 1 9 1 0 1 1 13
0 1 0 0 2 0 1 1 0 6 0 1 0 1 10 0 1 1 1 14
1 1 0 0 3 1 1 1 0 7 1 1 0 1 11 1 1 1 1 15
5. Reattach the digit and replace the weather cover.
Replacing batteries
Eventually, your batteries will fail to hold a charge and will need to be replaced. Batteries
can only be replaced with Powersonic PS1270 UL recognized (MH20845) gel cell
batteries. The deck clocks take 2 batteries, which should both be replaced at the same
time. These are available from Colorado Time Systems (part number R-420-003).
Tool required: #2 Phillips head screwdriver
1. Make sure the deck clock is disconnected from AC power and that the power
switch is turned off.
2. With clock standing on its feet, remove the screws from the battery covers using a
Phillips head screwdriver. Remove the battery covers and place them and the
screws in a safe place.
3.
Start with either of the clock’s feet. Unscrew the retaining bracket and remove it.
4. Slide the battery out, tipping the clock if necessary.
5. Disconnect battery cables from battery. Take care not to short the battery
terminals , for example by touching both of them with a screwdriver.
6. Connect battery cable to the new battery: red to red and black to black
7. Slide the battery back in, and secure it in place with the retaining bracket.