The Golight® RadioRay® Models 2067/2049 & 20674/02494
are designed to be permanently attached to a vehicle. The
2-Speed Searchlight with Directional Flexibility is controlled by
a wireless remote, or a wired dash mount control, which gives
the operator a full 370° horizontal rotation and a 135° vertical
tilt with fingertip control.
The RadioRay® provides superior light penetration with Cr5
PentaBeam™ technology in a halogen configuration or with
state of the art P-Vex™ lens and LED technology.
The RadioRay® Includes:
• RadioRay® Searchlight
• Wireless Remote Control
• Wired Dash Mount Remote Control
• 2 A23 12V Batteries
• Permanent Mounting Gasket
• Screw and Caps
• Rockguard (not Available with LED units)
MOUNTING INSTRUCTIONS
Determine location of dash-mount remote. Create an opening
and insert dash-mount remote with correlating quick connect
on 20’ cord. (Extra 10’ and 20’ quick connect harnesses are
available, if needed.) Connect power wires to 12 v D.C.
The 12 Volt DC power wire should be joined to the leads on the
20’ cable with appropriate automotive wire attachments. It is
critical that polarity be observed. The (+) lead of the Golight®
is marked with a red tag. The power should be fused at 10
Amps and be on a dedicated circuit or wired to an appropriate
automotive relay system.
Determine location for Golight®. The small arrow on the base
indicates the normal forward direction of the light. Create
opening for Golight® cord. Place gasket on Golight® and
attach correlating quick-connect to Golight®. Position the con-
nection point beneath the mounting surface and use silicone
sealant to fill opening around the harness. Set light in place
and mount light base to surface with screws provided. Cover
screws with the 4 caps provided.
NOTE: The small drain hole in the edge of the gasket should
normally face opposite the forward direction of the vehicle—
opposite the arrow molded in the front of the base. Silicone
or other like sealants should not be used around the base
gasket as it will limit the Golight’s ability to drain excess water
properly.
** Attach Dash-Mount Remote to designated location with screws.
Unit is installed.
PROGRAMMABLE REMOTE INSTRUCTIONS
The Golight® RadioRay® is controlled with a programmable remote
with 2187 different channels. This feature allows you the freedom
to change the channel selection, and the receiver relearns the new
selection.
PROGRAMMING THE TRANSMITTER.
This light has been pre-programmed at the factory, and it is not
necessary to re-program the transmitter, unless you experience
outside interference.
1. IMPORTANT: Disconnect power by removing fuse or disconnect
-
ing vehicle battery.
2. Remove battery cover from remote control.
3. Set the 7 dip switches to a selection of your choice. There are 3
positions on each; positive, negative and neutral. Use a small-
screwdriver and select a position for each dip switch. *Please
note that the orientation of the +/– switch positions may vary
among different models of wireless remote controls.
4. Insert both A23 12V batteries with the +/– in the same direction.
Be sure batteries have adequate charge.
5. Replace battery cover.
a. Depress the on/off button and hold it down. Red LED
will light.
b. While holding the on/off button down, reinstall the
power (replace fuse or connect vehicle battery).
c. Keep your finger on the on/off button for 5-6 seconds,
and then release. The light should now be programmed.
OPERATION OF GOLIGHT® RADIORAY® - Wireless Remote
1. Using the remote control, turn on the light by depressing the on/
off button.
2. With the 4-way arrows on the remote control, rotate your light
to the desired location. Depending upon conditions, the wireless
remote may be used up to 80 feet from the RadioRay®.
3. The speed of the light rotation can be controlled by depressing the
tortoise/hare button one time and by depressing it again to restore
the original speed.
4. The spotlight should not be turned on when the snap on lens
cover (rockguard) is attached. (Not applicable for LED)
OPERATION OF GOLIGHT® RADIORAY® - Dash Remote
1. Use the toggle switch on the dash control to turn the light on/
off.
2. The 4-way joystick on the dash control rotates your light to the
desired location.
BATTERY INSTALLATION AND DISPOSAL
• Remove Battery Cover: remove the phillips head screw
securing the battery cover then remove the cover. With the
battery compartment now exposed, insert batteries according
to correct polarity. Remove the batteries by gripping the
positive end of each battery and lifting.
For information regarding the proper disposal/recycling of the
batteries contact Golight at 800.557.0098
Use only 12v-A23 batteries in the Golight remote control
USAGE:
» This light is intended for off-road and utility use only
» This light is intended to be mounted outside the vehicle while
in use
» This light may only be disassembled and repaired by an
authorized representative
MISUSE:
» This light is not approved for road or highway use
» This light is not approved for underwater use
» This light is not approved for inverted mounting
» This light is not approved for use inside a vehicle or enclosure
and power should be removed prior to placing the light in such
circumstance
» This light may be damaged if operated in icing conditions
» This light may only be dismantled by an authorized Golight
representative
» Any violation of the above referenced misuses will be
considered grounds for warranty refusal