background image

     
 
 
 
 
 
 
 
                                           

 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 
 
DESA INTERNATIONAL 

2701 INDUSTRIAL DRIVE 

 

 

 

 

 

 

 

                                P/N 108919-01 

P.O. BOX 90024  

 

 

 

 

 

 

 

 

                                      

REV D 

BOWLING GREEN, KY 42101-9004 

 

 

 

 

 

 

                                         

6/02

 

www.desatech.com

 

SAVE THIS BOOK 

This book is valuable.  In addition to instructing you on
how to install and maintain your appliance, it also
contains information that will enable you to obtain
replacement parts or accessory items when needed.
Keep it with your other important papers. 

This fireplace is approved for use as a wood burning fireplace or for
use with a vented gas log approved to ANS Z21.60, Z21.84 or RGA
2-72 standards or for use with a vent-free gas log heater approved to
ANS Z21.11.2 standard.  A DESA hood must be installed when
using a vent-free gas log heater (see Accessories, p. 12). 

WARNING:  Always leave glass doors fully opened or fully closed when operating this fireplace.

C42MW 

42” Circulating Firebox 

Includes: Manual Variable Control Fan System, Combustion 

Air Kit and Bi-Fold Doors with Brushed Brass Finish 

 

INSTALLATION INSTRUCTIONS 

This firebox meets the construction and safety standards of H.U.D. for
application in mobile homes when installed according to these instructions. 

ALL DIMENSIONS IN THIS MANUAL ARE IN
INCHES UNLESS OTHERWISE SPECIFIED

 

Summary of Contents for C42MW
















Reviews: