8.2. Measure and test (MEAS)
The internal microprocessor of the
ProSpot 575 MB
allows for several diagnostic and output parameters to be
displayed. You may record, in this menu, determine the position in which the projector will come to rest when turned on with no dmx
signal attached.
A023
new DMX address
☞
menu
AOO1
☞
+
o
–
☞
+
o
–
MEAS
A023
DMX address
FUNC
☞
enter
☞
enter
V .F A N
voltage to fans
to measure the DC voltage to the fans located in the unit.
Values higher than 13,8V are anomalous.
1 3 .8 V
v oltage measurement
☞
enter
C H 0 1
f r o m c h 1
C H 22
to ch 22
1 0
DMX value
255
DMX value
☞
enter
☞
+
o
–
D M I N
DMX value on each channel
reading of DMX value (0/255), received by each
of the 22 channels on DMX 512 line.
☞
enter
☞
enter
R A T E
DMX rate
reading of DMX 512 signal value.
☞
enter
2 2
value reading
ND M X
no dmx signal
NO.AL
no alarm message
ALRM
a
larm
Reading of Warning message
sequences (errors) shown during reset
operation
☞
enter
☞
+
o
–
O P E R
alarm message
5 8 C
temperature measurement
TEMP
temperature
to measure the internal temperaturein C
°
☞
enter
☞
+
o
–
☞
+
o
–
☞
+
o
–
☞
+
o
–
☞
+
o
–
☞
+
o
–
☞
+
o
–
☞
+
o
–
0 0 0 0
☞
enter
☞
enter
es.
0 1 2 7
☞
+
o
–
P A N
pan movement
T I LT
tilt movement
D I M M
dimmer
activation
S H U T
shutter
activation
I R I S
iris
activation
F O C U
focus
activation
G O B 1
gobo wheel 1selection
G B P 1
gobo 1position
G B R 1
gobo 1 rotation
G O B 2
gobo wheel 2 selection
P R I S
p risma activation
C O L R
colour wheel selection
S T O R
to record the position of the unit and of its internal
components. If DMX signal is not applied, the recorded
setting will appear at the end of reset operation when
the unit is switched on.
☞
enter
0 1 2 8
☞
enter
☞
enter
☞
+
o
–
☞
enter
es.
0 1 2 7
S U R E
☞
enter
☞
enter
0 1 0 8
☞
enter
☞
+
o
–
☞
+
o
–
☞
+
o
–
☞
enter
es.
0 1 2 7
0 1 0 5
☞
enter
☞
+
o
–
☞
+
o
–
☞
enter
es.
0 1 2 7
☞
+
o
–
TEST
test
function test
☞
+
o
–
☞
enter
0 1 2 8
☞
+
o
–
☞
+
o
–
☞
enter
es.
0 1 5 0
☞
enter
☞
+
o
–
0 0 0 0
☞
+
o
–
☞
+
o
–
☞
enter
es.
0 1 2 7
☞
+
o
–
0 0 2 0
☞
enter
☞
+
o
–
☞
+
o
–
☞
enter
es.
0 1 2 7
☞
+
o
–
0 1 8 0
☞
enter
☞
+
o
–
☞
+
o
–
☞
enter
es.
0 1 2 7
☞
+
o
–
0 1 4 0
☞
enter
☞
+
o
–
☞
+
o
–
☞
enter
es.
0 1 2 7
☞
+
o
–
0 0 1 0
☞
enter
☞
+
o
–
☞
+
o
–
☞
enter
es.
0 1 2 7
☞
+
o
–
0 0 5 0
☞
enter
☞
+
o
–
☞
+
o
–
☞
enter
es.
0 1 2 7
☞
+
o
–
0 1 2 8
☞
enter
☞
+
o
–
☞
+
o
–
☞
enter
es.
0 1 2 7
☞
+
o
–
1 0
value reading
☞
+
o
–
☞
enter
☞
enter
☞
enter
☞
+
o
–
HOUR
working time
working time (in hours)
5 8 9
value reading
1 2 3 0
value reading
L I F E
lamp life after last reset
L I F S
life of all lamps
used on the unit
U N I T
projector life
☞
enter
N.B.: reset the
LIFE
value when
changing the lamp
14
English