background image

7

Automatic Convenience Options

The PowerCode PC 4300

TM

 performs a variety of automatic functions to

enhance security and comfort. Some of these features are programmable
at the time of installation. Please see your installer for further details.

Illuminated Entry

When the alarm system is disarmed, the vehicle courtesy lights will turn
on for 1 minute, or until the vehicle is started or the system is re-armed.

Illuminated Exit

When removing the key from the ignition, the vehicle courtesy lights
will turn on for 1 minute, or until the PowerCode

TM

 is armed.

Automatic Arming

The PowerCode PC 4300

TM

 will arm automatically 1 minute after the

key is removed from the ignition. This feature can be temporarily
disabled by placing the system into Valet mode.

Ignition Lock

If all doors are closed and the vehicle is started with the key, the doors
will automatically lock.

Ignition Unlock

When removing the key from the ignition, the doors will automatically unlock.

When Your Security System is Triggered

The Power Code PC 4300

TM

 will trigger if one of the following events

occurs while the system is armed:

• Any protected entrance is opened
• The vehicle ignition is turned on
• The vehicle is jolted hard enough to signal the impact detector

Once the alarm is triggered, the siren (or horn) sounds and the vehicle

parking lights flash for 30 seconds. The system will then re-arm, awaiting
the next intrusion attempt. To stop the siren while keeping the alarm armed
and doors locked, press the ARM button while the system is triggered.

The Interior Status Indicator

The Status Indicator is a high-intensity red light mounted in a visible
location on the vehicle dashboard. This red light gives a visual
indication of the alarm system’s state of operation. Note the chart
below:

If the Status Indicator is...

....then the Security System

Flashing Green

is disarmed

Flashing Slowly

is armed

Flashing Very Quickly

was triggered in your absence
(see Attempted Intrusion ID - page 4)

Flashing  Intermittently

is in Valet mode (LED is Green)

(2 flashes, off, 2 flashes)

On (not flashing)

is in Pre-arm mode

Summary of Contents for PC 4300

















Reviews: