Code Alarm CA 6151 Installation Manual Download Page 2

Page: 2 / 34

Before You Begin ...................................................................................... 4

Wire Connection Guide ........................................................................... 5

4 Pin Main Harness ................................................................................... 7

6 Pin Start Harness ................................................................................... 8

6 Pin Output Harness ............................................................................. 10

8 Pin Input Harness ................................................................................. 11

4 Pin Alternate Output Harness ............................................................. 14

3 Pin Door Lock Output Harness ........................................................... 16

Additional Ports ...................................................................................... 20

Antenna / LED / Programming Port ....................................................... 20

DBI Port .................................................................................................... 20

Tracking Port ........................................................................................... 20

Set Up & Programming .......................................................................... 21

Transmitter Programming ........................................................................ 21

Manual Feature Programming ................................................................. 21

Programming Feature Banks .................................................................. 22

Tach Programming .................................................................................. 23

Smart Tachless Mode ............................................................................. 24

Adjusting the Shock Sensor .................................................................. 24

Testing the Shock Sensor ...................................................................... 24

Chirp Delete - User Accessible .............................................................. 24

Dome Light Delay / Theater Dimming ..................................................... 25

Table of Contents

Summary of Contents for CA 6151

































Search results

Summary of Contents for CA 6151

Reviews:

Related manuals for CA 6151

Brands by name

Popular brands

Code Alarm CA 6151, Installation Manual

Search results

Summary of Contents for CA 6151

Reviews:

Related manuals for CA 6151

Brands by name

Popular brands