background image

3

2010 Audiovox Electronics Corporation. All rights reserved.

Using Your Remote Control

 Using the Keyless Entry

The   button is used to lock the vehicle's doors, the   button is used to unlock the
vehicle's doors. To lock or unlock the doors simply press and release the desired
function button one time. For your convenience, the parking lights will flash once
when the doors are unlocked and twice when the door are locked.

NOTE: The system is defaulted with Silent Choice enabled, which requires a
second press of the   or   button to activate an audible locking/unlocking
response from the vehicle. If your system is set up for 2 step unlock, a third press
of unlock will activate the audible response.

  Using the Progressive Car Finder Feature

Press the 

 button to locate your vehicle. The system will sound 5 times at low

volume, increasing in volume each time the button is pressed.

  Using the Personal Protection Alarm (Panic)

Press and hold the 

 button for 3 seconds to activate the personal protection

alarm. During panic mode, the normal function of the transmitter buttons will be
suspended. The transmitter’s   and   buttons can be used to lock and unlock the
door (if the option is installed). To stop the alarm, press and hold the 

 button on

the transmitter again for 3 seconds. The system will automatically stop after 30
seconds.

 Programmed Transmitter Notification

As a security precaution each time the vehicle’s ignition is turn on the status LED
light with flash the number of transmitters programmed into the system. This helps
to identify unauthorized transmitters from accessing your vehicle. If you believe an
unauthorized transmitter has been programmed to your system, contact your
installing dealer for assistance.

 Activating the Trunk Release Feature (Optional)

The     button is used to open the trunk of the vehicle. To open the vehicle's trunk
press and hold the     button for 3 seconds.

  Two Stage Door Unlock (Optional)

If this feature is enabled on your system, pressing the    button one time will
unlock only the driver’s door. Press   again within three seconds to unlock the
remaining doors.

Summary of Contents for CA 5051MT











Reviews: