Coda S12.5 Operational Manual Download Page 14

 13

WARRANTY & DISCLAIMER

i. Warranty - Any failure of the Amplifier S12.5, hereafter known as the product or 

original product, to operate or to meet specifications, applicable at time of 

manufacture, due to a manufacturing defect or component failure, will be 

corrected by Coda Technologies without charge for parts or labor, for a period of ten 

years from date of original purchase. Coda Technologies will provide for surface 

transportation to and from the factory for a period of one year from date of original 

purchase.

ii. Procedure - If the product should require service under warranty contact Coda 

Technologies at the location on the back cover of this manual for shipping 

instructions. Products purchased outside of the United States will be covered by the 

warranty conditions extended by the importing distributor which may differ from 

those given above.

vi. Unnecessary Service - In all conditions, if the product is submitted for service and 

found to be operated without fault and within specifications, shipping charges will be 

billed to the customer.

v. Subjective Differences - No guarantee is made that the product will perform to any 

specifications that cannot be measured and confimed with precision audio analysis 

equipment. Coda Technologies is only obligated to make repairs which will bring the 

product into compliance with the specifications stated in this manual.

This warranty gives you specific legal rights. You may have other rights which vary 

from state to state.

iv. Total Loss and Replacement - If the product is submitted for service due to a 

severe malfunction which has caused damage sufficient enough to make a repair 

attempt infeasible, the product will be replaced with another unit of equal or superior 

specifications.  Coda Technologies product line is frequently updated and changed, 

and the specific model and version of the original product may be discontinued at 

any time without notice. In this case no guarantees are made that the replacement 

unit will be visually similar to the original product.

iii. Exclusion of Coverage - Coda Technologies is not obligated to service the product 

in certain conditions, as according to the following subsections.

In these conditions any service will be made at Coda Technologies sole option.

b. The product has been transferred to a third party. This warranty is valid only for 

the original purchaser of the product. 

c. The product has been transported outside of the United States of America.

i. operation not in accordance with the instructions in this manual

a. The product has been damaged through:

ii. abuse, tampering, modification or accident

iii. serial number defacement

Disclaimer - Coda Technologies cannot be held responsible for any damage caused 

by their products, including but not limited to:

a. Damage to speakers caused by failure of a Coda Technologies product to 

mute or disable itself as expected or described in its manual.

b. Damage caused by connecting a load to a Coda Technologies product 

having an improper impedance as described in the products manual.

d. Damage caused by defects in design, construction or component quality.

Outside of the U.S., warranty is determined by local laws and regulations. 
Please contact your distributor for details in your area.

Summary of Contents for S12.5

















Reviews: