cocweb CF-A-GR Installation And Operation Instruction Manual Download Page 7 | Manualshive

Page: 7 / 12

cocweb CF-A-GR Installation And Operation Instruction Manual Download Page 7

Figure 12

Figure 13

7. FINISHING THE

INSTALLATION

Step 1. Tuck connections neatly into ceiling
outlet box.

Step 2. Slide the canopy up to hanger bracket
and place the key hole on the canopy over the
screw on the hanger bracket, turn canopy until
it locks in place at the narrow section of the
key holes. (Fig. 12)

Step 3. Align the circular hole on canopy with
the remaining hole on the hanger bracket,
secure by tightening the two set screws. Note:
Adjust the canopy screws as necessary until
the canopy and canopy cover are snug.

Warning: Make sure tab at bottom of hanger
bracket is properly seated in groove of hanger
ball before attaching canopy to bracket.
Failure to properly seat tab in groove could
cause damage to electrical wiring.

Outlet box

Hanger
bracket

Canopy

Canopy cover

Screws

8. ATTACHING THE FAN

BLADES

Step 1. Insert the blade through the blade slot
in the decorative housing. Align the holes in
blade and blade arm as showing in Figure 13,

secure with fiber washers and screws
provided.

Step 2. Repeat this procedure for remaining
blades.

6

Blades

Screws and fiber
washers

Slot

making sure the holes are also aligned and

«
...
5
6
7
8
9
...
»

Summary of Contents for CF-A-GR













Reviews:

No comments